Page 1
Water Specialist WS15P Control Valve Parts and Service Manual HYDROCARBONS SUCH AS VASELINE®, PETROLEUM JELLY, KEROSENE, BENZENE, GASOLINE, ETC., WILL DAMAGE PRODUCTS THAT CONTAIN O-RINGS OR PLASTIC COMPONENTS. EXPOSURE TO SUCH HYDROCARBONS MAY CAUSE THE PRODUCTS TO LEAK. DO NOT USE CLACK CONTROL VALVE PRODUCT(S) ON WATER SUPPLIES...
WS15P Parts and Service Manual Page 3 Table of Contents General Specifications ..........................4 Drive Cap Assembly, Pistons, Stack Assembly, Main Body ............... 5 Regenerant Components ..........................6 Injectors ..............................7 Injector Flow Graphs - U.S. Units ......................8 Injector Flow Graphs - Metric Units ......................9 Fitting Kits..............................
Page 4 WS15P Parts and Service Manual General Specifications Minimum/Maximum Operating Pressures 20 – 125 psi (138 kPa – 862 kPa) Minimum/Maximum Operating Temperatures 40° - 110° F (4° - 43° C) Power Adapter: U.S. International Supply Voltage 100VAC to 120VAC...
O-RING 347 V4400-NPT WS15P NPT BODY ASSEMBLY V4400-BSPT WS15P BSPT BODY ASSEMBLY V4430-01** WS15P FTG ASY QC TO NPT 1 set of 2 V4430-02** WS15P FTG ASY QC TO BSPT V3641 O-RING 225 FOR VALVE BODIES WITH NPT THREADS V3441 O-RING 226 FOR VALVE BODIES WITH BSPT THREADS *V3174 Regenerant Piston not used for Backwash Only valves.
WS15P Parts and Service Manual Page 7 WS 1.5” Injectors Downflow Drawing Order No. Description Nozzle Color Typical Tank Quantity Diameter V3010-15B WS1.5 Injector Asy B Violet 12” V3010-15C WS1.5 Injector Asy C 13” V3010-15D WS1.5 Injector Asy D White 14”...
Page 8 WS15P Parts and Service Manual WS 1.5” Injector Flow Graphs - U.S. Units RED, ORDER NO. V3010-15C WHITE, ORDER NO. V3010-15D VIOLET, ORDER NO. V3010-15B ORDER NO. V3010-15B ORDER NO. V3010-15B ORDER NO. V3010-15C ORDER NO. V3010-15D US Units...
WS15P Parts and Service Manual Page 9 WS 1.5” Injector Flow Graphs - Metric Units WHITE, ORDER NO. V3010-15D VIOLET, ORDER NO. V3010-15B RED, ORDER NO. V3010-15C ORDER NO. V3010-15B ORDER NO. V3010-15C ORDER NO. V3010-15D Metric Units Metric Units...
• Slide nut on first, then the split ring and o-ring. • Hand tighten the nut only. Clack Order No. V4430-01 Clack Order No. V4430-02 Description: WS15P QC to NPT Fitting Kit Description: WS15P QC to BSPT Fitting Kit Drawing No. Order No. Description Quantity Drawing No.
WS15P Parts and Service Manual Page 11 Drain Line Flow Control Washers Drain Line Flow Controls Order No. Description V3162-XXX V3162-xx V3162-007 .7 GPM Drain line flow control Flow Rate Identi cation V3162-010 1.0 GPM Drain line flow control 5/8"...
Page 12 WS15P Parts and Service Manual Troubleshooting Procedures Problem Possible Cause Solution a. No power at electric outlet a. Repair outlet or use working outlet b. Control valve Power Adapter not plugged into b. Plug Power Adapter into outlet or connect...
Page 13
WS15P Parts and Service Manual Page 13 Problem Possible Cause Solution a. Bypass valve is open or faulty a. Fully close bypass valve or replace b. Media is exhausted due to high water usage b. Check program settings or diagnostics for abnormal water usage c.
Page 14
Page 14 WS15P Parts and Service Manual Problem Possible Cause Solution a. Motor not inserted full to engage pinion, motor a. Disconnect power, make sure motor is wires broken or disconnected fully engaged, check for broken wires, make sure two pin connector on motor is connected to the two pin connection on the PC Board labeled MOTOR.
Page 15
WS15P Parts and Service Manual Page 15 Problem Possible Cause Solution a. Control valve programmed for ALT A or b, a. Press NEXT and REGEN buttons for 3 nHbP, SEPS, or AUX MAV with out having a seconds to resynchronize software with...
Page 19
“SOFTENER AND FILTER CONTROLS LIMITED WARRANTY” 4/21/2022 PAGE 5: V4430-01** WS15P FTG ASY QC TO NPT 1 set of 2 V4430-02** WS15P FTG ASY QC TO BSPT ** Inlet/Outlet fitting kits are sold separate, see page 10 for fitting selection.
Page 20
Page 20 WS15P Parts and Service Manual CLACK CORPORATION SOFTENER AND FILTER CONTROLS LIMITED WARRANTY Clack Corporation (”Clack”) warrants to OEM that its Softener and Filter Control Valves will be free from defects in material and workmanship under normal use and service for a period of five years from the date of shipment of such Valves from Clack’s plant in Windsor, Wisconsin when installed and operated within recommended...