JL Audio Slash v2 450/4V2 Owner's Manual page 12

aPPendix a:
Precise Frequency selection Chart
"Filter Freq" CH 1&2 / CH 3&4
detent Panel actual
number marking Freq.
Full counter-clockwise: 58
01 . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
02 . . . . . . . . . . . "50" . . . . . . . . . . . .58
03 . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
04 . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
05 . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
06 . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
07 . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
08 . . . . . . . . . . . "60" . . . . . . . . . . . .63
09 . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
10 . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
11 . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
12 . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
13 . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
14 . . . . . . . . . . . "75" . . . . . . . . . . . .77
15 . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
16 . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
17 . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
18 . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
19 . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
20 . . . . . . . . . . . "95" . . . . . . . . . . . .97
21 . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
22 . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
23 . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
24 . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
25 . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
26 . . . . . . . . . . "130" . . . . . . . . . . 135
27 . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
28 . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
29 . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
30 . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
31 . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
32 . . . . . . . . . . "200" . . . . . . . . . . 223
33 . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
34 . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
35 . . . . . . . . . . . . . . . . . . . . . . . . . . . 337
36 . . . . . . . . . . . . . . . . . . . . . . . . . . . 404
37 . . . . . . . . . . . . . . . . . . . . . . . . . . . 474
38 . . . . . . . . . . "500" . . . . . . . . . . 514
Full-clockwise: 542
22 | JL Audio - 450/4 Owner's Manual
v2
aPPendix b:
input sensitivity level setting
aPPendix a:
input sensitivity level setting
JL Audio amplifiers utilizing the Regulated
Intelligent Power Supply (R.I.P.S.) allow
delivery of their rated power when connected
to any load impedance from 1.5 - 4Ω per
channel and when connected to a charging
system with any voltage from 11 - 14.5V. This
design is beneficial for many reasons. One of
these reasons is ease of setup. Because each
JL Audio amplifier will always deliver the
same amount of power within its operational
range of impedances and supply voltages, the
maximum, unclipped output is very predictable.
This makes setting the gain structure via the
input sensitivity controls very simple. Following
the directions below will allow the user to adjust
the input sensitivity of the amplifier(s) simply
and easily in just a few minutes using equipment
which is commonly available in installation bays.
necessary equipment
• Digital AC Voltmeter
• CD with a sine-wave test tone recorded at
0 dB reference level in the frequency range
to be amplified for that set of channels
(50 Hz for subwoofer channels, 1 kHz for
a midrange application). The CleanSweep®
Calibration Disc contains the appropriate
test tones and is available for sale at
http://store.jlaudio.com Do not use attenuated
test tones (-10 dB, -20 dB, etc.).
the nine-step Procedure
(follow this procedure for each pair of channels)
1) Disconnect the speaker(s) from the
amplifier's "Front Speaker Outputs" and
"Rear Speaker Outputs" connectors.
2) Turn off all processing on the source
unit (bass/treble, loudness, EQ, etc.).
Set fader control to center position
and subwoofer level control to 3/4 of
maximum (if used to drive the 450/4v2).
3) Switch the "Input Voltage" to "Low" and
turn the "Input Sens." control on both sets of
channels all the way down.
4) Set the source unit volume to 3/4 of full
volume. If either set of channels is being
driven by a source unit's dedicated subwoofer
output, also adjust the source unit's subwoofer
level control to 3/4 of maximum output. This
will allow for reasonable gain overlap with
moderate clipping at full volume.
5) Using the chart below, determine the
target voltage for input sensitivity
adjustment according to the nominal
impedance of the speaker system
connected to each set of outputs.
6) Verify that you have disconnected the speakers
before proceeding. Play a track with an
appropriate sine wave (within the frequency
range to be amplified by each set of channels)
at 3/4 source unit volume.
7) Connect the AC voltmeter to the "CH 1&2
Speaker Outputs" or "CH 3&4 Speaker
Outputs" connectors of the amplifier. If the
channel pair is operating in stereo, it is only
necessary to measure one channel. If bridged,
make sure you test the voltage at the correct
connectors (L+ and R–).
CHannels 1&2
nom.
impedance
stereo
8Ω
24.5 V
6Ω
24.5 V
4Ω
24.5 V
3Ω
21.2 V
2Ω
17.3 V not recommended
1.5Ω
15.0 V not recommended
8) Increase the "Input Sens." control until
the target voltage is delivered for that set
of channels. If excessive voltage is read
on either set of channels with the control
at minimum (full counterclockwise),
switch the appropriate "Input Voltage"
switch to "High" and re-adjust.
9) Once you have adjusted each set of channels to
its maximum unclipped output level, reconnect
the speaker(s). The "Input Sens." controls can
now be adjusted downward if either or both
sets of channels requires attenuation to achieve
the desired system balance.
!
IMPORTANT
Do not increase any "Input Sens." setting in
the system beyond the maximum level
established during this procedure. Doing so
will result in audible distortion and possible
speaker damage.
It will be necessary to re-adjust the "Input
Sens." for the affected channels if any equalizer
boost is activated after setting the "Input
Sens." with this procedure. This applies to
any EQ boost circuit, including the amplifier's
"Bass EQ" and source unit tone controls or EQ
circuits. EQ cuts will not require re-adjustment.
CHannels 3&4
bridged stereo bridged
49.0 V 17.3 V 34.6 V
42.4 V 17.3 V 30.0 V
34.6 V 17.3 V 24.5 V
30.0 V 15.0 V 21.2 V
12.2 V not recommended
10.6 V not recommended
23