Table of Contents
Advertisement
owner's manual
monoblock subwoofer amplifier
Thank you for purchasing a JL Audio amplifier for
your automotive sound system.
Your amplifier has been designed and manufactured to exacting
standards in order to ensure years of musical enjoyment in your vehicle.
For maximum performance and extended warranty
coverage, we highly recommend that you have your new amplifier
installed by an authorized JL Audio dealer. Your authorized
dealer has the training, expertise and installation equipment to ensure
optimum performance from this product. Should you
decide to install the amplifier yourself, please take the time
to read this manual thoroughly so as to familiarize yourself
with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this
manual or any aspect of your amplifier's operation, please contact your
authorized JL Audio dealer for assistance. If you need further assistance,
please call the JL Audio Technical Support Department
at (954) 443-1100 during business hours.
Advertisement
Table of Contents
Related Manuals for JL Audio Slash v2 1000/1V2
Summary of Contents for JL Audio Slash v2 1000/1V2
- Page 1 If you have any questions regarding the instructions in this manual or any aspect of your amplifier’s operation, please contact your authorized JL Audio dealer for assistance. If you need further assistance, please call the JL Audio Technical Support Department...
-
Page 2: Protect Your Hearing
(pg. 5) (pg. 6) +12VDC Ground Remote 1000 /1 Monoblock Subwoofer Amplifier 2 | JL Audio - 1000/1 Owner’s Manual Cooling efficiency Considerations: Your JL Audio amplifier employs an advanced type of heat management, called RealSink™. This feature takes advantage of convection and radiation effects to remove heat from the amplifier circuitry. -
Page 3: Product Description
+12VDC Ground Remote wire. For optimal grounding, we recommend the use of a JL Audio ECS master ground lug (XB-MGLU). Alternatively, a sheet metal screw or bolt can be used with a star washer. 1000 /1... -
Page 4: Remote Turn-On
RCA cables or plugs or use the Full Range | Amp Filter | Out Filter 12dB | 24dB Off | On 4.3 20 JL Audio ECS Speaker Wire to RCA adaptor Filter Mode Bass EQ (XB-CLRAIC2-SW). LP | HP... -
Page 5: Crossover Controls
Experiment to find the slope which best matches the acoustic requirements of your system. 8 | JL Audio - 1000/1 Owner’s Manual A trunk mounted sub whose The above hint is not “set-in-stone”…... - Page 6 Unlike conventional amplifiers that require Do not chassis ground any speakers connected a specific impedance to produce optimum to this or any other JL Audio amplifier. Doing so power, the R.I.P.S.-equipped 1000/1v2 gives will cause the amplifier to go into protection and you the freedom to use a variety of subwoofer mute the output.
- Page 7 If your amplifier fails or malfunctions, please return it to your authorized JL Audio dealer so that it may be sent in to JL Audio for service. Keep in mind that any large amplifier, like the There are no user serviceable parts or fuses inside the amplifier.
- Page 8 1000/1v2) at 3/4 these reasons is ease of setup. Because each source unit volume. JL Audio amplifier will always deliver the 7) Connect the AC voltmeter to the speaker output same amount of power within its operational connectors of the amplifier.
- Page 9 39 ......198 Full-clockwise : 198 16 | JL Audio - 1000/1 Owner’s Manual...
- Page 10 Full Range | Amp Filter | Out Filter “Preamp Output” are inactive. Left Output Right Output 18 | JL Audio - 1000/1 Owner’s Manual 3) The input sensitivity of the two amplifiers needs to be adjusted independently. To properly calibrate the amplifiers for maximum, identical, clean output, please refer to Appendix A (page 14).
- Page 11 Check the nominal load impedance to verify that the amplifier is driving a load between 1.5 - 4Ω. JL Audio monoblock amplifiers have two “+” positive connections and two “–”...
- Page 12 Output Mode Filter Slope Full Range | Amp Filter | Out Filter 12dB | 24dB Left Output Right Output Filter Freq. (Hz) 22 | JL Audio - 1000/1 Owner’s Manual Infrasonic Filter “Q” Center Freq. Boost (dB) Mode Off | On 4.3 20...
- Page 13 - amPliFiers (usa) JL AUDIO warrants this product to be free of defects in materials and workmanship for a period of ninety (90) days from the original date of purchase. The warranty term is extended to two (2) years if installation is performed or approved by an authorized JL AUDIO dealer (proof of installation or approval required on purchase receipt).
Need help?
Do you have a question about the Slash v2 1000/1V2 and is the answer not in the manual?
Questions and answers
Why when I wire this amp up the blue light is flashing
The blue "Low V" LED on the JL Audio Slash v2 1000/1V2 amplifier flashes when the amplifier is cycling on and off due to a voltage problem. Possible causes include a bad ground on the amplifier, battery, or alternator; a faulty battery or charging system; or an issue with a fuse holder or wire connection. Investigating and resolving the voltage issue is necessary to stop the flashing.
This answer is automatically generated