inVENTer sMove Operation Instructions Manual
Hide thumbs
Also See for sMove:
- User manual (60 pages) ,
- Quick operation manual (2 pages) ,
- Quick operation manual (2 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for inVENTer sMove
Summary of Contents for inVENTer sMove
- Page 1 Operation instructions sMove Control unit www.inventer.eu...
-
Page 2: Table Of Contents
The copyright to this document remains with the manufacturer. Safety instructions ......................4 Rights to all content and images: © inVENTer GmbH 2022. System overview: Controller sMove ..................6 All trademarks used in this document are the property of their respective manufacturers and are Construction ........................ -
Page 3: User And Safety Instructions
A signal word in front of the text also The sMove controller (also referred to as "controller" or "sMove" in the following text) is only to be indicates the hazard level. If several hazard levels occur, the safety note for the highest level is used to control the decentralised iV ventilation devices with heat recovery from inVENTer GmbH. -
Page 4: System Overview Controller Smove
It is available in the variants s4 or s8, each in two versions (standard or flat). The controller sMove consist of a mounting plate for installation on the inner wall, and a control panel. The control panel contains the electronic components of the controller and the control... - Page 5 DC voltage is set in the house control unit. Controller sMove with closed interface Depending on the control voltage, the ventilation and heat recovery operating modes are possible in ventilation stages 1 - 4, as well as switching off the connected ventilation devices (for control The external interface is a bifunctional interface on the back of the control unit.
-
Page 6: Operation
Repeated pressing switches the connected ventilation devices on again. Completely switching off the ventilation The controller sMove consist of a mounting plate for installation on the inner wall, and a control devices is not possible in the flat model. -
Page 7: Initial Commissioning
LED display Operating modes Orange Heat recovery When the sMove controller is commissioned for the first time, the reversing fans of the ventilation Blue Ventilation devices start automatically in the lowest ventilation stage (25 %) in the heat recovery operating mode. -
Page 8: Activating/Deactivating The Pause Function
Pause remaining time display If the sMove controller is in pause, the remaining time in which the controller is in pause can be The reversing fan of the ventilation device is switched off for a set period of time. The ventilation viewed. -
Page 9: Confirming Filter Change
≥ 1 sec ler lights up. The filter change interval is reset to 180 days. The ventilation level is set. ≥ 5 sec The filter change has been confirmed. Controller sMove | Operation instructions Controller sMove | Operation instructions... -
Page 10: Viewing Operating Hours
The LED to the left of the button corresponds to the number 0. The controller sMove ist virtually maintenance free. The service work can be carried out by the user after a short instruction. The LED to the left of the sliding controller corresponds to the... -
Page 11: Accesories And Spare Parts
Product Material Disposal Control panel casing Plastics recycling Control panel glass plate Acryl glass Residual waste Circuit board / Switching Electronic parts Collection point for electronic equipment power supply unit Controller sMove | Operation instructions Controller sMove | Operation instructions... -
Page 12: Warranty And Guarantee
Outside Germany, the national warranty regulations of the country in which the system is sold apply. Contact the dealer of your home country. Guarantee: inVENTer GmbH gives a 5-year guarantee on all electronic components. This covers premature product wear. Warranty and guarantee claim For information on the guarantee provisions, see www.inventer.eu/garantie/guarantee. - Page 13 GmbH Ortsstraße 4a D-07751 Löberschütz www.inventer.eu Subject to modifications No liability for printing errors Product Number 5012-0030 Version: 1.0 – 09/2022...
Need help?
Do you have a question about the sMove and is the answer not in the manual?
Questions and answers