Page 1
Read these instructions carefully before use and keep them for future reference. Your child’s safety may be affected if you do not follow these instructions. The InStep Bicycle Trailer must be assembled by an adult who has read and understands the instructions in this manual.
Page 2
Thank You For purchasing the InStep Bicycle Trailer. You will be sure to enjoy hours of pleasurable exercise and family time. If you have any questions or comments our customer service hours are: 8:00 AM - 5:00 PM Monday through Friday CST.
• Check the trailer (pram) body or seat unit attachment devices using the product. are correctly engaged before use. • Use caution to avoid pinch points when folding or unfolding • Always use the crotch strap in combination with the waist belt. the trailer. 1 InStep Sync Trailer...
• The trailer requires a wide turning radius. Do not turn sharply. Sharp changes in direction may cause a tip over. • Check the trailer for damage. Do not use if damaged. • Be sure the fasteners are tight. Tighten if necessary. continued on next page InStep Sync Trailer...
• The maximum weight that can be carried in the cabin pockets is 1 lb. each. The maximum weight that can be carried in the rear storage area is 5 lbs. • Attach a rearview mirror on the bicycle to check on the (child/ children) in the trailer. 3 InStep Sync Trailer...
Parts and Features Note: The following accessories can be ordered from www.instep.net. Safety Flag Additional Coupler Kits (includes; with pole coupler plate, tab washer and locking pin). Elastic bands for weather shield Safety harness system Canopy Weather shield (rolls up and fastens in elastic bands)
• Keep children clear when folding or unfolding the trailer. • Ensure that all locking devices are engaged before use. ❶ Unfold the side walls upward to a vertical position. Figure 3.1 Figure 3.1 Figure 3.2 5 InStep Sync Trailer...
Page 9
❸ Rotate the crossbar into the crossbar latch. Figure 3.3 ❹ Check the crossbar is locked into place by pulling up and down on it. Figure 3.4 Release button Crossbar latch Crossbar Figure 3.4 Figure 3.3 InStep Sync Trailer...
❸ Attach the hook and loop fasteners to the canopy to the strips on the front and back of the frame walls. ❹ Roll the weather shield up into the bands at the top of the canopy if you are not using Figure 3.5 7 InStep Sync Trailer...
❹ Insert the locking pin through both the bracket and tow bar. ❺ Slide the metal safety loop on the end of the locking pin. Check that it is securely in place. Figure 3.7 Figure 3.6 Figure 3.7 InStep Sync Trailer...
Interlock the gear on the wheel with the gear on the rear brake. Figure 3.8 ❷ Push the wheel into the bracket until you hear the axle click into place. Note: shown from underside of the frame. Figure 3.8 Figure 3.9 9 InStep Sync Trailer...
❶ Assemble the flag pole sections by sliding the top half of the pole into the opening of the bottom half of the pole. ❷ Insert the flag pole into the sleeve located at the rear corner of the trailer. Figure 3.10 Figure 3.10 InStep Sync Trailer...
❸ Place the tab washer on the axle. Fit the tab into the slot on the bicycle frame dropout. Note: If your bicycle frame doesn’t Figure 4.2 have a slot in the drop out, rotate the tab to fit into the axle slot. Figure 4.3 Slot washer Figure 4.3 11 InStep Sync Trailer...
Page 15
❹ Remove the locking pin from the coupler and slide the coupler ❻ Place the hub nut and washer back onto the axle and tighten. off the end of the tow bar. Figure 4.5 Incorrect coupler placement Coupler Washer Hub nut Figure 4.4 Figure 4.5 InStep Sync Trailer...
Important! Ensure the loop of the safety pin is facing away from the wheel to prevent possible friction against the wheel and spokes of the bicycle. Figure 4.6 Inner Skewer Spring Outer Quick spring release lever Quick release lever and spring Figure 4.6 Figure 4.7 13 InStep Sync Trailer...
Page 17
❻ Rotate the quick release lever up and tighten. When properly tightened, the quick release lever should leave an imprint in your hand. The pressure should be firm but not excessive. Quick release lever and spring Slot washer Figure 4.9 Figure 4.8 InStep Sync Trailer...
Page 18
This reduces stress on the tow bar. Figure 4.10 from the wheel to prevent possible friction against the wheel and spokes of the bicycle. ❽ Insert the locking pin into the hole on the top of the coupler. Figure 4.10 Figure 4.11 15 InStep Sync Trailer...
Tow bar ring ❶ Wrap the tow bar safety strap around the bicycle frame. Figure 4.12 Bicycle frame Safety strap Safety strap Figure 4.12 Figure 4.13 InStep Sync Trailer...
Tighten as needed. Figure 5.1 To remove the child from the trailer: Unfasten the clips from the lap buckle. Pull the straps away from the body and remove the child from the trailer. Figure 5.1 17 InStep Sync Trailer...
❹ Pull the strap and anchor all the way through to the back. Make sure the strap is properly anchored on the seat back. Repeat these steps for the opposite strap. Figure 5.2 Figure 5.2 InStep Sync Trailer...
❷ Unfasten the clip on the safety strap from the tow bar ring, and unwrap it from the bicycle frame. Clip the strap back onto the D-ring of the tow bar. Figure 6.1 Figure 6.1 Figure 6.2 19 InStep Sync Trailer...
❶ Remove the flag pole and separate the flag pole sections. ❷ Remove the wheels by: Figure 6.4 Figure 6.3 a. Pulling the wheel release lever out and hold. b. Remove the wheel. c. Release the lever Figure 6.3 Figure 6.4 InStep Sync Trailer...
Page 24
❺ Place the locking pin back through the tow bar and bracket walls. Remove the canopy from the frame. Figure 6.6 Note: Coupler plate will remain assembled to bike 99% of the time Figure 6.5 Figure 6.6 21 InStep Sync Trailer...
Page 25
Crossbar release button ❿ Store in a dry place. Important! If the storage area is hot then release the some air from the tires. This will help prevent excessive expansion or popping. Crossbar latch Crossbar Figure 6.7 Figure 6.8 InStep Sync Trailer...
To make a claim under warranty, notification of such defect must be given to Pacific Cycle, Inc. the address stated on the previous page. You will be instructed on how the product or part needing replacement should be shipped postpaid to Pacific Cycle, Inc. 23 InStep Sync Trailer...