Page 1
Read these instructions carefully before use and keep them for future reference. Your child’s safety may be affected if you do not follow these instructions. The InStep Bicycle Trailer must be assembled by an adult who has read and understands the instructions in this manual.
Page 2
Thank You For purchasing the InStep Bicycle Trailer. You will be sure to enjoy hours of pleasurable exercise and family time. If you have any questions or comments our customer service hours are: 8:00 AM - 5:00 PM Monday through Friday CST.
• Never use the trailer with children who cannot sit unaided • Use caution to avoid pinch points when folding or unfolding • Check the trailer (pram) body or seat unit attachment devices the trailer. are correctly engaged before use. InStep Robin Trailer...
• Allow extra clearance for the trailer when near curbs, parked • Over inflation of tires may result in failure and risk of serious cars, and other obstacles. injury. Do not exceed maximum pressure as shown on tires. continued on next page InStep Robin Trailer...
• The maximum weight that can be carried in the cabin pockets is 1 lbs. each. The maximum weight that can be carried in the rear storage area is 5 lbs. • Attach a rearview mirror on the bicycle to check on the (child/ children) in the trailer. InStep Robin Trailer...
Safety harness system Canopy Weather shield(rolls up and fastens in elastic bands) Storage area Zip-in/zip-out bug screen Back panel Front panel Bicycle coupler Wheels (2) Tow bar Clear plastic windows Safety strap InStep Robin Trailer...
The front and back panels are tucked under the side walls. ❶ Pull the front panel out from under the side walls to expose the front of the frame. Notice the locking spring pin holes on each end of the frame. Figure 3.1 Figure 3.1 InStep Robin Trailer...
Page 9
❸ Lift the right side wall up into a vertical position. Figure 3.3 locking spring pins insert into the holes on both ends. Be sure the frame is securely locked together. Figure 3.2 Locking spring pin in hole Side rail Side rail Right wall Figure 3.2 Figure 3.3 InStep Robin Trailer...
Page 10
❺ Lock the crossbar into the crossbar latch. Figure 3.5 will rotate towards the crossbar latch. Figure 3.4 ❻ Check the crossbar is locked into place by pulling up and down on it. Figure 3.5 Left wall Release button Crossbar latch Crossbar Figure 3.4 Figure 3.5 InStep Robin Trailer...
❽ Snap the panel closed. Figure 3.6 ❶ Starting at the bottom corner of the trailer, snap the first set of snaps from the canopy to the frame on both sides. Figure 3.7 Back panel Figure 3.6 Figure 3.7 InStep Robin Trailer...
❷ Remove the locking pin from the tow bar bracket. Figure 3.9 Figure 3.8 ❹ Roll the weather shield up into the bands at the top of the canopy if you are not using it. Figure 3.8 Figure 3.8 Figure 3.9 InStep Robin Trailer...
Page 13
Figure 3.10 locking pin. Check the locking pin is securely in place. Figure 3.10 ❹ Insert the locking pin completely through the hole in the end of the tow bar and bracket. Locking pin Safety loop Figure 3.10 InStep Robin Trailer...
❷ Insert the locking pin into the axle and slide the end of the safety loop over the end of the locking pin. Check that the locking pin is securely in place. Figure 3.11 Figure 3.11 Figure 3.12 InStep Robin Trailer...
Note: Remove the coupler plate and tab washer from the end of the tow bar before proceeding. Slot ❶ Using a wrench, remove the hub nut and washer from the bicycle’s back wheel. Figure 4.1 Axle slot Tab washer Figure 4.2 Washer Hub nut Figure 4.1 InStep Robin Trailer...
Page 16
Align the pegs on the back of Figure 4.4 the plate with the holes in the tab washer. Figure 4.3 Washer Hub nut Coupler pegs Coupler plate large hole Figure 4.3 Figure 4.4 InStep Robin Trailer...
Page 17
❽ Wrap the tow bar safety strap around the bicycle frame and Figure 4.6 clip it to the ring on the end of the tow bar. Figure 4.8 Bicycle frame Safety loop Safety strap clip Safety strap Locking pin Tow bar ring Figure 4.6 Figure 4.8 InStep Robin Trailer...
Figure 4.9 face out ❷ Remove the axle skewer and spring. Leave the wheel in place. Figure 4.10 The wide end of the spring must face out, touching the lever Figure 4.10 Figure 4.11 InStep Robin Trailer...
Page 19
❼ Follow step 5 - 8 on page 13. Figures 4.5 - 4.8 Fit the tab on the tab washer into the slot on the bicycle frame dropout Figure 4.12 Figure 4.13 InStep Robin Trailer...
Tighten as needed. Figure 5.1 To remove the child from the trailer: Unfasten the clips from the lap buckle. Pull the straps away from the body and remove the child from the trailer. Figure 5.1 InStep Robin Trailer...
D-ring on both sets of safety harnesses into the center D-ring. Then, snap the right shoulder harnesses. Figure 5.2 strap from the left set of safety harness into the center D-ring. Figure 5.3 Figure 5.2 Figure 5.3 InStep Robin Trailer...
❹ Bring the waist strap across the child’s hips, and fasten the buckle. Tighten as needed. Figure 5.4 To remove the child from the trailer: Unfasten the clips from the lap buckle. Pull the straps away from the body and remove the child from the trailer. Figure 5.4 InStep Robin Trailer...
❷ Unfasten the clip on the safety strap from the tow bar ring, and unwrap it from the bicycle frame. Clip the strap back onto the D-ring of the tow bar. Figure 6.1 Figure 6.2 Figure 6.1 InStep Robin Trailer...
Page 24
Remove the locking pin from the axle, and pull the wheel out of the hole in the frame bracket. c. Slide the locking pin back into the frame hole ❸ Remove the locking pin from the tow bar bracket. Figure 6.4 Figure 6.4 Figure 6.3 InStep Robin Trailer...
Page 25
❾ Place any loose items such as the canopy and wheels inside the passenger compartment. ❿ Store in a dry place. Important! If the storage area is hot then release the some air from the tires. This will help prevent Unsnap Figure 6.6 excessive expansion or popping. InStep Robin Trailer...
To make a claim under warranty, notification of such defect must be given to Pacific Cycle, Inc. the address stated on the previous page. You will be instructed on how the product or part needing replacement should be shipped postpaid to Pacific Cycle, Inc. InStep Robin Trailer...
Need help?
Do you have a question about the Robin and is the answer not in the manual?
Questions and answers