Related Manuals for Keg King Thermentor King
Summary of Contents for Keg King Thermentor King
- Page 1 Thermentor King User Manual Thermentor King Compact Fermentation Temperature Control System User Instruction Manual https://www.kegking.com.au Keg King is a registered business name of MCH Australia Pty Ltd...
-
Page 2: Warnings And General Safety
Keg King sells food-grade glycol for this application. Please read the entire manual before operating. https://www.kegking.com.au Page 2 of 16 Keg King is a registered business name of MCH Australia Pty Ltd... -
Page 3: Table Of Contents
Preparing the Coolant ........................... 12 Priming the Pump ..........................12 General Operation ............................. 14 Setting the Temperature and Other Settings ..................14 Troubleshooting............................16 https://www.kegking.com.au Page 3 of 16 Keg King is a registered business name of MCH Australia Pty Ltd... -
Page 4: Keg King
Check the resellers map on our website to find where our products are available in North America, UK, EU, Aus, NZ and South Africa. https://www.kegking.com.au/retailers Since 2009, Keg King’s mission is to make the best brewing & dispensing equipment in the world! Check out our helpful instructional videos on the Keg King YouTube Channel https://www.youtube.com/c/KegKingvideos... -
Page 5: Introduction
Thermentor King User Manual Introduction The Thermentor King (released in 2021) is a low-cost system designed to use a glycol mixture for controlling temperature in small fermenters and kegs. It has a generous capacity for heating (150 watts) that will keep a fermenter warm on the coldest days. -
Page 6: Unboxing
(may be included (may be included) e.g. Apollo 30L Fermenter Keg King part code 8340-2 Keg King part code Keg King part code 10605 4734 https://www.kegking.com.au Page 6 of 16 Keg King is a registered business name of MCH Australia Pty Ltd... - Page 7 Keg King part code 8336-500 Pipe insulation sleeves for the coolant tubing Water for the circulating coolant Available from hardware stores 250 - 350ml https://www.kegking.com.au Page 7 of 16 Keg King is a registered business name of MCH Australia Pty Ltd...
-
Page 8: Getting To Know The Unit
Thermentor King User Manual Getting to Know the Unit The Unit https://www.kegking.com.au Page 8 of 16 Keg King is a registered business name of MCH Australia Pty Ltd... -
Page 9: The Temperature Control Panel
Power consumption: ≤3W Sensor: NTC sensor (1PC) Relay contact capacity: Cool 10A/250VAC; Heat 10A/250VAC Ambient temperature: 0~60°C Storage temperature: -30~75°C Relative humidity: 20%~85% (No condensate) https://www.kegking.com.au Page 9 of 16 Keg King is a registered business name of MCH Australia Pty Ltd... -
Page 10: Initial Setup
You will need to acquire tubing with ball lock (liquid) disconnects to make the coolant circuit between the Thermentor King and a cooling coil in your fermenter or Keg. This tubing should be as short as practically possible and be fully covered by foam pipe insulation (available from hardware stores etc.). -
Page 11: Connecting To The Fermenter
Thermentor King User Manual Connecting to the Fermenter 1. Connect the coolant lines from the coolant connections on the Thermentor King to the fermenter Cooling Coil 2. Connect the temperature sensor cable to the sensor connection on the unit. 3. Insert the temperature sensor into the fermenter thermowell. If the fermenter does not... -
Page 12: Preparing The Coolant
8. Continue to top-up the priming reservoir, without overflowing it. You should be able to observe the coolant level drop as the coolant circuit fills. https://www.kegking.com.au Page 12 of 16 Keg King is a registered business name of MCH Australia Pty Ltd... - Page 13 To remove the bubbles, tilt the flow indicator vertically so that the coolant flows through it in the upward direction. The bubbles should work their way up and out. https://www.kegking.com.au Page 13 of 16 Keg King is a registered business name of MCH Australia Pty Ltd...
-
Page 14: General Operation
5°, it will start heating until it reaches 5°. F3 is a cooling delay setting which can be set to zero as the Thermentor King can switch between cooling and heating without ill effects. If the unit has been actively... - Page 15 While continuing to hold the “S” button, use the up and down arrow buttons to set the desired value. Press the power button to save the set value. https://www.kegking.com.au Page 15 of 16 Keg King is a registered business name of MCH Australia Pty Ltd...
-
Page 16: Troubleshooting
Set the temperature to 20C and it should unfreeze within a few minutes. If it does not, there is another issue. Or coolant is flowing too slowly. https://www.kegking.com.au Page 16 of 16 Keg King is a registered business name of MCH Australia Pty Ltd...
Need help?
Do you have a question about the Thermentor King and is the answer not in the manual?
Questions and answers