Table of Contents
Advertisement
Quick Links
142-BR300
Portable edgebander for ABS
Operationg instructions
Distributor:
IGM nástroje a stroje s.r.o.
Ke Kopanině 560, 252 67, Tuchoměřice
Czech Republic, EU
Phone: +420 220 950 910
E-mail: sales@igmtools.com
Website: www.igmtools.com
PDF ONLINE
www.igmtools.info
2022-07-12
142-BR300 IGM Portable Edgebander for ABS Manual EN v2.5.00 A4ob
Advertisement
Table of Contents
Related Manuals for IGM BR300
Summary of Contents for IGM BR300
- Page 1 Operationg instructions Distributor: IGM nástroje a stroje s.r.o. Ke Kopanině 560, 252 67, Tuchoměřice Czech Republic, EU Phone: +420 220 950 910 E-mail: sales@igmtools.com Website: www.igmtools.com PDF ONLINE www.igmtools.info 2022-07-12 142-BR300 IGM Portable Edgebander for ABS Manual EN v2.5.00 A4ob...
-
Page 2: Table Of Contents
Dear customer, This manual contains important instructions and information for the installation and proper use of the BR300 edgebander. This manual is part of the machine and therefore it should not be kept elsewhere than in the vicinity of the machine so that you can be consulted at any time by you or other persons operating the machine. -
Page 3: Warranty Service
The warranty is subject to Terms and Conditions and onto the new owner. Warranty Conditions of IGM nástroje a stroje s.r.o., the current version of which are available at www. Any alterations or changes to the machine are igmtools.com. -
Page 4: Risks
Operating instructions EN 3.3 Risks minutes before storing it in the portable case. That Risk exists even when using the machine according to way, the glue in the container will cool down to 60°C. the manual. Use a piece of cloth to wipe any adhesive residues on WATCH OUT! Heated glue may reach the the machine. -
Page 5: Technical Data
Warm-up time(120 °C) 4min Fuse F 6A (230V) Cable length Glue pot capacity 400ml 4.3 ContentsIGM BR300 Portable Edgebander for ABS IGM Worktable Light transport case Sample tape from calibration procedures pic. 2 5. TRANSPORT, UNPACKING AND ASSEMBLY 5.1 Transport and unpacking Fig1 The machine is not assembled due to transport. -
Page 6: Control And Gauge Set Up On The Supporting Table
Operating instructions EN 6.1.2 Control and gauge set up of the support table 6.1.3 Adjusting the amount of applied glue The amount of glue is pre-set and should suit the The pre-set support table is perpendicular to the pressure plate. Place the support table on a mitre gauge (pic.2, majority of operations. -
Page 7: Fastening The Workpiece Before Edgebanding
Make sure the edge of the workpiece you will edgeband extends beyond the edge of your worktop. It may be more comfortable to use a vacuum suction cup. You can order one from IGM as an optional accessory. Use of the vacuum cup (pic.8) pic.10 pic. -
Page 8: Operating The Machine
Operating instructions EN 7. OPERATING THE MACHINE every two months or every 50 hours of operation 7.1 Edgebanding of the edgebander. Remove the rest of the glue and Check for debris or dust in the glue pot, turn on refill with a new one the main switch and trigger the heating next to the display. -
Page 9: Malfunction Assistance
IGM Lever Valve for Vacuum Clamp M964 M966-01 IGM PD80 Edgeband Trimmer IGM Plastic T-splitter for Vacuum Clamp M964 142-PD80 M966-02 IGM End Trimmer for Shaped and Straight Panels M951-V IGM Fachmann Edge Banding Hand Trimmer M950-00001 IGM Worktable for Edgebander and Trimmer for 142-ST95A DR500-BR300 www.igmtools.com... - Page 10 IGM nástroje a stroje s.r.o., Ke kopanině 560, Tuchoměřice, 252 67, Czech Republic, E.U. +420 220 950 910, www.igmtools.com © 2022 IGM nástroje a stroje s.r.o.