Table of Contents
Advertisement
66
GETTING STARTED
Installation
continued
You do not need to preset the stations if you have already set them automatically (see Plug & Auto Set Up)
Presetting the stations automatically
Your VTR contains a built-in tuner used to receive
Note : To enable the VTR to decode a scrambled TV station, the
television broadcasts.
decoder must be activated after the scan (see pages 18).
You must preset the stations received through the
1
tuner. This can be done:
• Plug & Auto Set up (see page 11)
2
• Automatically
• Manually (see page 17)
DISPLAY
3
4
COUNT.RST
F.ADV
CLR/RST
5
CURSOR
OK
AUDIO
NOTE :
The time and date are set automatically from the broadcast
signal. If the signal is weak or ghosting occurs, the time and date
may not be set automatically. In this case, they should be set
manually (see page 13).
Once the auto scanning procedure has finished, some stations
may have been stored more than once; select the stations with
the best reception and delete the ones no longer required (see
page 19)
6
16
Press MENU on the remote control.
Result : The programming menu is displayed.
Press the corresponding ›, ‚ or ¥, Š button to select the
INSTALLATION option.
PROG
OPTIONS
INSTALL
CLOCK
BONUS
LANG
INSTALLATION
›‚ ¥Š
OK
END:
MENU
Press the OK button to select this option.
Result : The INSTALLATION menu is displayed.
Press the corresponding › or ‚ button, until the AUTO SET UP
option is selected. And then press the Š button to select this
option.
Result : A message appears, indicating that any channels
already preset on your VTR will be deleted.
YOUR DATA WILL BE LOST
PRESS
OK
TO CONTINUE
MENU
TO EXIT
Press OK to start the auto scanning.
Result :
The PLEASE WAIT indication flashes on the television screen.
AUTO SET UP
PLEASE WAIT
60%
I˚˚˚˚˚˚˚˚----------I
END:
MENU
The first frequency band is scanned and the first station
found is displayed and stored.
The VTR then searches for the second station and so on.
When the automatic scanning procedure has finished, the
VTR switches automatically to programme.
Note : The number of stations automatically stored by the VTR depends
on the number of stations that it has found(reception conditions, etc)
If you wish to cancel the auto scanning before the end, press the MENU
button three times to exit the menu.
66
GETTING STARTED
Installation
continued
You do not need to preset the stations manually if you have already set them automatically.
Presetting the stations manually
1
Press MENU on the remote control.
Result : The programming menu is displayed.
2
Press the corresponding ›, ‚ or ¥, Š buttons to select the
INSTALLATION option.
DISPLAY
3
Press the OK button to select this option.
Result : The INSTALLATION menu is displayed.
COUNT.RST
4
Press the › or ‚ buttons, until the MANUAL SET UP option is
F.ADV
CLR/RST
selected.
5
Press the Š buttons to select this option.
CURSOR
Result : The TV STATION TABLE menu is displayed.
OK
AUDIO
6
Press the › or ‚ button to select a programme number as
required.
7
Press the Š button to preset the station.
Result : The MANUAL TUNING menu is displayed.
PROG
OPTIONS
INSTALL
CLOCK
BONUS
LANG
INSTALLATION
›‚ ¥Š
OK
END:
MENU
INSTALL
AUTO SET UP
MANUAL SET UP
VCR OUTPUT CH
:CH36
›‚
Š
END:
MENU
** TV STATION TABLE **
PR
CH
NAME
1
002
----
2
3
4
5
›‚ Š
SWAPPING:
OK
DELETE:
CLR/RST
MENU
** MANUAL TUNING **
PR
: 1
CH
: 004
MFT
: -
NAME
: ----
›‚ ¥Š
MEMORY:
OK
END:
MENU
17
Advertisement
Table of Contents
