Download Print this page

Advertisement

Quick Links

If you are missing parts or have any questions about this product, contact our customer service representative first!
You can also order parts by writing to the address listed below. Please include the product model number,
color and a detailed description of the part.
*
Failure to follow these warnings and assembly instructions could result in serious injury or death.
*
Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.
*
Before each usage or assembly, inspect crib for damaged hardware, loose joints, missing parts or
sharp edges, DO NOT use crib if any parts are missing or broken. Ask your dealer or write to our
customer service representative (address & phone number shown above) for replacement parts and
instructional literature if needed. DO NOT substitute parts.
*
Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional
padding under an infant.
*
When child is able to climb out or reaches the height of 35 inches (90 cm), the crib shall no longer
be used.
*
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to
sleep, unless otherwise advised by your physician.
DO NOT place crib near window where cords from blinds or drapes may strangle a child.
*
*
Strings can cause strangulation! DO NOT place crib with a string around a child's neck, such as
hood strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
*
To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
If refinishing, use a non-toxic finish specified for children's products.
*
*
When child is able to pull to standing position, set mattress to lowest position and remove bumper
pads, large toys and other objects that could serve as steps for climbing out.
*
Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
DO NOT use a water mattress with this crib.
*
Replace teething rail if damaged or loose (if teething rail is provided for this model).
*
*
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 INCHES BY 51-5/8
INCHES (69CM BY 131CM) WITH A MINIMUM THICKNESS OF 4 INCHES (10CM) BUT NOT
EXCEEDING 6 INCHES (15CM).
Infants can suffocate in gaps between crib sides and a mattress that is too small.
*
Follow warnings on all products in a crib.
*
*
Ensure all parts and components are present before beginning assembly.
*
Assemble on soft, smooth surface to prevent damage to product finish.
*
Phillips head screw driver is not included.
*
DO NOT use power tools.
*
CAUTION: Adult assembly required.
*
Assembly will require two people.
CUSTOMER SERVICE
CALL 1-800-295-1980
Customer Service Department No. 413
12345 Albert-Hudon Boulevard, Suite 100
Montreal, Quebec
Canada H1G 3L1
E-MAIL: csr@jardcoent.com
WARNING
NOTES
DA0930B- CRIB

Advertisement

loading

Summary of Contents for Jardine DA0930B

  • Page 1 DA0930B- CRIB CUSTOMER SERVICE If you are missing parts or have any questions about this product, contact our customer service representative first! CALL 1-800-295-1980 You can also order parts by writing to the address listed below. Please include the product model number, color and a detailed description of the part.
  • Page 2: Care And Cleaning

    Check bolts/screws periodically and tighten them if necessary. LIMITED WARRANTY Jardine Enterprise warrants its product to be free from defects in material and workmanship and agrees to remedy any such defect. This warranty covers 1 year from the date of original purchase.
  • Page 3 HARWARE AND PARTS LIST...
  • Page 4 NOTE: WHEN INSERTING SCREWS, TURN CLOCKWISE UNTIL TIGHT THEN LOOSEN 1/2-3/4 OF A TURN. AFTER CRIB IS FULLY ASSEMBLED, RETURN TO EACH SCREW AND TIGHTEN. USE WAX OR SOAP ON ALL SCREWS TO FACILITATE ASSEMBLY. STEP 1 Attach stationary side (G) to end panels (F1 & F2) using bolts (B).
  • Page 5 STEP 2: Attach the mattress support to the 4 corner posts with the mattress support bolts ( C). Use Allen Wrench to tighten bolts. Refer to details 1 and 2 for direction on how to properly attach the mattress support. INCORRECT- Raised edge should face...
  • Page 6 STEP 3 ALIGN AND SLIDE DROP SIDE FROM THE BOTTOM ONTO THE DROP SIDE UPPER AND LOWER TRACKS ON THE LEFT AND RIGHT FRONT POSTS. MAKE SURE THE RELEASE LATCH ON THE LOWER GUIDES IS TO THE OUTSIDE OF THE LOWER DROP SIDE TRACKS (PULL TOWARDS YOU). RAISE DROPSIDE UNTIL IT IS LOCKED INTO PLACE. CAUTION: DO NOT FORCE THE DROP SIDE AS YOU MAY BREAK THE LOCKS, GUIDES, OR TRACKS.