Page 2
- Fixed base dimensions on page 15 February 25, 2019 - Edited Reference info Errors in this publication can be reported to the Manufacturer. Refer to Section 7 for contact information and address attention to the Engineering Department. Valcom Manufacturing Group Inc...
GENERAL INFORMATION AND SAFETY PRECAUTIONS 1-1. SAFETY PRECAUTIONS. When working in the vicinity of the VHF Antenna AS-3226B/URC, make sure the antenna is deenergized in accordance with the WARNING in paragraphs 4-3 and 4-4, and when testing the antenna, make sure the test equipment is properly grounded in accordance with WARNING in paragraph 4-4.
AS-3226B/URC VTM-01-009-RevE Table 1-1. Reference Data Parameter Specification Nomenclature Antenna AS-3226B/URC Manufacturer Valcom Manufacturing Group Inc 35736 Frequency Range 30 to 88 MHz Impedance 50 ohms VSWR less than 3.0:1 Polarization Vertical Power Capability 800 watts Gain 0 dBi Radiation Pattern...
PRD Electronic shooting Bridge Type 3302 Standing Wave General Radio HP Model 415B Indicator Type 1234 Electronic HP Type HP Type 5246L Counter 5340A Insulation Resistance Trouble- Megohmmeter Freed Type 1620 greater than 1 shooting megohm Valcom Manufacturing Group Inc...
AS-3226B/URC VTM-01-009-RevE SECTION 2 OPERATION 2-1. GENERAL. The AS-3226B/URC Antenna has no operating controls or indicators. It operates only when the ship's VHF receiving and transmitting equipment is operated. Valcom Manufacturing Group Inc...
FUNCTIONAL DESCRIPTION 3-1. FUNCTIONAL DESCRIPTION. The AS-3226B/URC VHF Antenna is a general purpose, high performance, vertically polarized, broadband, balanced dipole covering the 30 to 88 MHz frequency range. It is used for either transmitting or receiving. The antenna is a cylindrical dipole radiator fed by a conventional coaxial RF line.
ETN3 can perform the task. b. Visually check painted surfaces for wear, chipping, etc. Paint the antenna with grey epoxy enamel (MIL-P-24441). A technician with a minimum rating of ETN3 can perform this task. Valcom Manufacturing Group Inc...
Title of Test. The title of the test to be performed is VSWR Test. d. Minimum Rating of Technician. A technician with a minimum rating of ETN3 can perform this task. e. VSWR Test Setup. Figure 4-1 shows the VSWR test setup for the antenna. Valcom Manufacturing Group Inc...
(e) Read VSWR on standing wave indicator on SWR scale. Test Values. If VSWR is 3.0:1 or greater, internal damage is indicated. Corrective Action. Refer to table 5-3 for corrective actions. Figure 4-1 VSWR Test Setup Valcom Manufacturing Group Inc...
5-1. INTRODUCTION. Transmission trouble in the receiving or transmitting system of which the AS-3226B/URC VHF Antenna is a part may be caused by trouble in the antenna, in another piece of equipment, or in the transmission line. If trouble occurs, check to determine that the equipment and the RF transmission line being used with the antenna are functioning properly before attempting to follow the procedures described in this section.
RF connector assembly in antenna. 1. Defective RF connector High VSWR (greater than 3.0:1) or RF gasket. as indicated by VSWR test Replace antenna. described in paragraph 4-4. 2. Defective internal assembly in antenna. Valcom Manufacturing Group Inc...
AS-3226B/URC VTM-01-009-RevE SECTION 6 CORRECTIVE MAINTENANCE 6-1. INTRODUCTION. No corrective maintenance can be performed on the AS-3226B/URC VHF Antenna. 6-2. ADJUSTMENTS AND ALIGNMENT. No adjustments and alignment are applicable to the antenna. 6-3. REPAIR. No repair of the antenna or any of its parts is applicable.
Table 7-1. List of Parts Table 7-2. List of Manufacturers a. List of Parts. Table 7-1 lists the parts of the AS-3226B/URC Antenna as shipped. b. List of Manufacturers. Table 7-2 contains the name, address, and Federal Supply Code for Manufacturers of the manufacturers supply items for the equipment as referenced in Table 7-1.
SECTION 8 INSTALLATION 8-1. SITE INFORMATION. The AS-3226B/URC VHF Antenna is designed primarily for shipboard installation. The antenna can also be used at shore installations. The antenna should be installed in a non-obstructed environment, preferably more than 30 feet from any contiguous structures, such as masts, bulkheads, or other metal objects.
VTM-01-009-RevE 8-7. INSTALLATION CHECKOUT. Checkout of the antenna after installation can only be accomplished by operating the ship's receiving and transmitting equipment that is used with the antenna. Figure 8-1 Installation Data of the AS-3226B/URC Antenna Valcom Manufacturing Group Inc...