1. Manuals
  2. Brands
  3. Emery Manuals
  4. Sports & Outdoors
  5. TM100
  6. Operation manual

Emery TM100 Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TM100
Operation
Manual
© 2022 Emery Game Line

Advertisement

Table of Contents
loading

Related Manuals for Emery TM100

Summary of Contents for Emery TM100

  • Page 1 TM100 Operation Manual © 2022 Emery Game Line...

  • Page 2: Table Of Contents

    • Setting up an R-Series Radius Tool (R24 or R33) …... Pages 12-15 • Using an R-Series Radius Tool (R24 or R33) ………………... Page 16 • Maintenance and Storage …………………………………………. Page 17 • Warnings, Recommendations, and Liability ……………..Page 18 © 2022 Emery Game Line...

  • Page 3: Get To Know Your Machine

    Get to Know Your Machine Handle The important features of the TM100 Taping Machine are called out below. Tape Drum Tape Drum Axle Pointer Adapter Rear Wheel Wheel Collar Pointer Tape Guide Guide Bar Front Radius Wheel Attachment Hole © 2022 Emery Game Line...

  • Page 4: Getting Started

    Getting Started To begin taping, the following items will be needed: • TM100 Taping Machine • 1 set of G-Series tape guides • 2 tape guide screws and wingnuts • 1 pointer assembly © 2022 Emery Game Line Page: 2...

  • Page 5: Machine Set-Up

    • If you are only going to be taping using one roll of tape, be sure to set up the tape guide as close to the center of the machine as possible. Center of the machine © 2022 Emery Game Line Page: 3...
  • Page 6 Machine Set-Up STEP 2: Measure the gap between the two inside walls of • the tape guides to make sure it is correct. © 2022 Emery Game Line Page: 4...
  • Page 7 Other notes: • Make sure tape width matches the Tape Guide width. • Tape roll should be a tight press fit onto the tape drum. Back edge of Sticky side up Tape Drum © 2022 Emery Game Line Page: 5...
  • Page 8 • The Tape Drums are hard to move because they need friction to hold their position on the Tape Drum Axle. • Misalignment of the Tape Drums and Tape Guides will cause wrinkles in the tape. © 2022 Emery Game Line Page: 6...
  • Page 9 Machine Set-Up STEP 5: Attach Pointer to the TM100 using the thumbscrew • and wingnut as shown. Align the Pointer with the ground before • tightening the thumbscrew all the way. Other notes: • Make sure rounded side of point is toward the ground.
  • Page 10 Keep the pointer aligned with your guiding-line on • the surface and slowly roll the machine forward to set tape. Other notes: • It is recommended to start taping a few inches before where tape is required. © 2022 Emery Game Line Page: 8...

  • Page 11: Laying Tape

    • Applying downward pressure will remove the most air pockets from the tape and create a sealed edge for painting. • Rolling the machine too fast will put excessive stress on the machine and provide poor taping results. © 2022 Emery Game Line Page: 9...

  • Page 12: Using A Minorly Offset Guiding-Line

    Other notes: • Loosening the screws will only allow for an offset of about 1.5” both ways. See next page for achieving a larger offset. Gap between 1.5” offset tape lines guiding-line © 2022 Emery Game Line Page: 10...

  • Page 13: Using A Majorly Offset Guiding-Line

    Adapter to hold the position. Other notes: • Do not over-tighten the screws, they will strip-out the threads in the adapter. • Not recommended for offsets over 6 inches. Gap between 6” offset tape lines guiding-line © 2022 Emery Game Line Page: 11...

  • Page 14: Setting Up An R-Series Radius Tool (R24 Or R33)

    Setting Up an R-Series Radius Tool (R24 or R33) The important features of the R-Series Clevis Radius Tool are called out below. Radius Quick Tool Point Release Radius Tool Adapter Thumbscrew Handle Cable © 2022 Emery Game Line Page: 12...
  • Page 15 • Press the quick release pin into the radius tool • attachment hole as shown. Set the TM100 Taping Machine at the location • where the line will begin. Push down slightly to hold the position of the machine. © 2022 Emery Game Line...
  • Page 16 Other notes: • It is recommended to put down a few layers of tape where the radius tool point will be used. This will avoid damage to the surface. © 2022 Emery Game Line Page: 14...
  • Page 17 Pull excess cable through the adapter until there is • tension in the cable. Tighten the two thumbscrews to hold the length of • the cable. Other notes: • Do not overtighten the thumbscrews. This will damage the cable. © 2022 Emery Game Line Page: 15...

  • Page 18: Using An R-Series Radius Tool (R24 Or R33)

    One person holds the Radius Tool Handle and • applies pressure on the point. Person 2 The second person pushes the TM100 Taping • Machine forward, allowing the machine to follow the curved path. NOTE: Be sure to apply downward pressure to the machine.

  • Page 19: Maintenance And Storage

    • sun or on hot surfaces for extended periods of time. Store in the up-right position as shown. Remove pointer. • Other notes: • Contact Emery Game Line to ask about refurbished machines. © 2022 Emery Game Line Page: 17...

  • Page 20: Warnings, Recommendations, And Liability

    Liability Emery Game Line in not liable for the following: • Damage to the surface in which the TM100 Taping Machine is being used on. • Damage to the machine caused by user error. • Poor quality of taped or painted lines.

Table of Contents