Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Eddylight Pro EDDY-HW-01
Summary of Contents for Eddylight Pro EDDY-HW-01
- Page 1 EDDYLIGHT PRO COOL SPARKLER MACHINE USER MANUAL MODEL: EDDY-HW-01...
-
Page 2: Package Contents
Package Contents Included in delivery: • 1 x cold spark machine; • 1 x power cord; • 1 x signal cable; • 1 x remote controller DMX Instruction The machine adopts 3-pin signal wire connection (5-pin can be customized), with DMX IN and DMX OUT double interfaces, which can be used for multiple connections and is suitable for standard 512 signal control. -
Page 3: Indicator Description
Indicator Description 8 8 8 READY FAULT HEAT DMX ADD READY ： Green light When the "READY" green light turns from flashing into light on, it indicates that the machine is ready to work. DMX ： Blue light Flashing shows that DMX signal is connected, otherwise no signal. FAULT ：... - Page 4 Power ： (Signal connection) Short press 1second is connect the machine, the display will show “FHH” after connected, then “FHH” will change to special effects address as below show, that’ s connected successful. Long press 3 seconds is unconnected, the display show “OFF”, then change to “001”...
- Page 5 Operation Instruction There have two operate modes: DMX 512 console, Remote controller. Please ensure sufficient consumables before use; After added consumables, Cover the rubber plug (don’t add to wrong fountain hole) The hole add consumables 1) Use remote do normal fountain: Short press “Power”...
- Page 6 2) Use remote do special effects fountain: Press “Power” to connect the machine, the display show “FHH” that be connected successful. To adjust each machine special effects address code by each machine address code button as picture show The display will show number or letter(A、 B、 C、 D、 E、 F are correspond number10 to 15 respectively), like below picture show “3”...
- Page 7 Push the second channel do fountain. 2nd channel do fountain (adjust the fountain height from up to down) End of event -- Clean powder (cleaning operation refer to point 7) 1st channel down a little bit clean powder (between 221-239) Remark: The detail channel instruction, please refer to attached channel operation;...
-
Page 8: Clean And Maintenance
Consumables save: Consumables should be kept in a dry and sealed environment to prevent moisture.(wet and sundry consumables should not be used) Consumables add: Pls stop running the machines before add the consumables, to avoid accidental injury. Clean and Maintenance Clear powder ：... -
Page 9: After-Sales
After-sales Warranty ： 1 Year (Subject to the date of manufacture) Each machine is affixed with the factory code. The factory code shall be provided when enjoying the warranty service. It is invalid if torn. It’ s may need provide some videos or pictures to confirm the problems. Fault light (yellow) display and processing method Display content Fault causes... -
Page 10: Warnings And Cautions
Warnings and Cautions The hole for adding Warning: High temperature warning, powder high temperature at exit. The sign is to remind users of paying attention to risk and security.Please note that the machines are not meant to be a continuous duration effect. The maximum running time is 30 second and can be repeated but should not be done to overheat the machine. - Page 11 The machine built-in protection procedures, will stop auto. once do fountain over 30s each time. If need it to work again, please operate the second channel again. The continuous shooting time is too long, the internal temperature will rise sharply and cause permanent damage. Suggest not do continuous shooting over 1minutes.
- Page 12 Outlook function description Remote receiver Dust Net signal Cooling Fan Display Spray Hole Indicator Adjust Buttons Powder hole Fuse Parameter Label Paws Power Switch DMX Port Cleaning hole Power Port Foldable Handle Factory Code Access Hole Product Parameters Double DMX input, 1-5 m Working Height Interface...
- Page 13 DMX Channel (2 Channels) 0-10 11-220 221-239 240-255 1st channel Pre-heat Emergency Clear Pre-heat Function turn off stop Powder turn on Add. code Add. E57 0-500 Display 0-15 16-39 40-63 64-87 88-111 112-135 2nd channel Turn off Fountain 1 Fountain 2 Fountain 3 Fountain 4 Fountain 5...
Need help?
Do you have a question about the Pro EDDY-HW-01 and is the answer not in the manual?
Questions and answers