Related Manuals for CAMION Ice Master H Series
Summary of Contents for CAMION Ice Master H Series
- Page 1 ICE MASTER H-SERIES ® OWNER’S MANUAL 3-POINT SPRAYER WITH HITCH Product Code: IMH050 Version 1.1 Copyright © Enduraplas. All Rights Reserved.
-
Page 2: Table Of Contents
English CONTENTS INTRODUCTION WARNINGS 4 - 7 GETTING STARTED 8 - 15 CALIBRATING 16 & 17 MAINTAINING 18 & 19 TROUBLESHOOTING 20 & 21 WARRANTY 22 - 25 PARTS BREAKDOWNS - ICE MASTER ® 26 - 35 H-SERIES Ice Master H-Series ®... -
Page 3: Introduction
English INTRODUCTION Congratulations! You now own a Camion™ sprayer. Durable design and construction assure you a lifetime of extreme performance. No sprayer is tougher. No sprayer will last longer. Take a look through this owner’s manual to learn how the pros use their Camion™... -
Page 4: Warnings
English WARNINGS 1. Do not exceed vehicle manufacturers loading, towing or lifting specifications and regulations. 2. Ensure tank is firmly secured in an appropriate manner. 3. Use caution at all times, particularly when driving on rough terrain. 4. Comply with chemical manufacturers safety requirements and all relevant legislations. - Page 5 English 13. No modifications and/or alterations may be made to this sprayer. Any such modifications not only void the sprayer warranty but can make the unit dangerous to anyone operating the pump. 14. Always inspect hoses and piping to avoid burst injuries. 15.
- Page 6 English 23. Never leave the sprayer unattended without turning off the pump, relieving the line pressure, and flushing the sprayer of any harmful chemicals. 24. You must be in good mental health to operate this sprayer and not be under the influence of alcohol or any drugs that could impair your vision, physical strength, dexterity, judgement, or other mental capacity.
- Page 7 English COMPATIBLE LIQUIDS Calcium Chloride Brine, Salt Brine and Premium Branded Liquids. Caution: Brine that contain tacky substances or solid particles may clog pumps and nozzles. These are not recommended. Warning: DO NOT USE any products that contain petroleum or petroleum by-products of any kind. These destroy seals and will void warranty.
-
Page 8: Getting Started
English GETTING STARTED Setting Up Your Sprayer 1) Remove hose from under sprayer and coil up hose on the two brackets mounted on top of tank. 2) Connect the spray gun in the wand clips. 3) Remove mounting point pins from accessory box and install on the two sprayer mounting points. - Page 9 English GETTING STARTED Mounting Your Boom 1) Take the four 3/8” x 1-1/2” carriage bolts and feed them through the back of the boom and install the 3/8” SS flat washer then the 3/8” SS lock washer and loosely install 3/8” SS hex nut. 2) Slide boom down adjustable brackets, guiding the carriage bolts into the slots.
- Page 10 English GETTING STARTED Hooking Up Sprayer 1) Back the tractor up to the sprayer aligning tractor hitch points with the arms at the height of the two lower mounting points. 2) Hook the two lower tractor hitch arms to the mounting point pins on sprayer, then secure with lock pin.
- Page 11 English GETTING STARTED Add On Options 1) If you ordered an optional hose reel with your unit, take hose reel from under the sprayer and set on top of tank opposite to lid end. 2) Secure hose reel frame to tank with provided hardware.
- Page 12 English GETTING STARTED Add On Options 1) If you purchased an optional receiver hitch mount, unpackage hitch and provided pins. 2) Take 3/4” x 4-1/4” quick connecting gold pins and insert into two lower mounting points connecting receiver hitch to unit. 3) Then, take 7/8”...
- Page 13 English GETTING STARTED Add On Options 5) Align holes on hitch and receiver and install lock pin. 6) Route your wire harness to desired power supply (making sure wire is not pinched or kinked). Version 1.1...
- Page 14 English GETTING STARTED Operating Your Sprayer 1) Take tank lid off and fill tank at least a quarter full with water, enough to run through the system to check all components are functioning correctly and are leak free. 2) Ensure the inline valve between tank and pump is in open position (parallel to hose) to allow the liquid to flow from the tank to the pump.
- Page 15 English Watch Instruction Videos: www.youtube.com Discover More Helpful Tips: www.IceControlTraining.com Version 1.1...
-
Page 16: Calibrating 16
English CALIBRATING Note: Always double check your application rates. The rate/acre listed is only based off the center section (not the two side nozzles) Ice Master H-Series ®... - Page 17 English GPM = Gallons Per Minute GPA = Gallons Per Acre GAL/1000 FT = Gallons Per 1000 Square Feet W = Nozzle spacing Gallons Per Minute Formula: GPA x MPH x W (per nozzle) 5,940 Gallons Per Minute Formula: GAL/1000FT x MPH x W (per nozzle) Gallons Per Acre Formula: 5,940 x GPM (per nozzle) MPH x W...
-
Page 18: Maintaining 18
English MAINTAINING Keeping your sprayer in good condition will help you lengthen the life of the sprayer. Everyone knows a well maintained piece of equipment ensures a longer life span. Sprayer maintenance can seem a huge task if you don’t have the right tools. - Page 19 English If required If damaged Every 250 operating hours o once a year After the first 5 operating hours Weekly or every 40 operating hours At the end of work and/or daily Before starting work Version 1.1...
-
Page 20: Troubleshooting 20
English TROUBLESHOOTING CONDITION CAUSE REMEDY Pump will not 1) Air leak on suction 1) Tighten/replace prime plumbing fittings & hose 2) Blocked/Restricted clamps. Verify suction intake hose hoses are in good 3) Filter cap condition disengaged 2) Remove blockage 3) Filter gasket from suction line, damaged/missing ensure line is not... - Page 21 English CONDITION CAUSE REMEDY Pressure gauge 1) Plugged with debris 1) Un-thread, check not registering and clean pressure gauge Hand gun loses 1) Debris in hose or 1) Un-thread nozzle pressure nozzle tip and clean 2) Pump losing prime 2) See Remedy for 3) Pump pressure ‘Pump will not prime dropping/fluctuating...
-
Page 22: Warranty
English WARRANTY LIMITED WARRANTY 1. Poly Tank Limited Warranty - Subject to other terms in this Limited Warranty, Manufacturer warrants to the original end user that this Tank will be free from material defects caused during the manufacturing process for a period of 5 years from the Purchase Date provided such warranty to the original end user shall be extended to 10 years from the Purchase Date if the original end user registers the Tank with Manufacturer within 30 days of the... - Page 23 English 3. Limitation of Liability under the Limited Warranty - In addition to those warranties disclaimed and excluded in clause 2 above, Manufacturer expressly further limits its warranty and liability under the Limited Warranty as set forth below in this clause 3. 3.1.
- Page 24 English 3.2. Without limiting the generality of clause 3.1: Manufacturer will not be liable for any personal injury, indirect or incidental damages, consequential losses, loss of liquids, loss of profit or any like claims whatsoever arising from any use of, or incidental to, or repairs to any of the Goods by a party other than Manufacturer;...
- Page 25 English 5. Claims and Questions - If you have questions about this Limited Warranty or to make a warranty claim, contact Manufacturer at: customercare@enduraplas.com 6. Definitions - For this Limited Warranty the following definitions apply: Manufacturer means Enduraplas LLC. Purchase Date means the date upon which the applicable goods were purchased by the original end user.
-
Page 26: Parts Breakdowns - Ice Master
OVERVIEW 30 39 CPA0367 VIEW A VIEW B VIEW C IMSB7H-H IMSHMB01 Ice Master H-Series ®... - Page 27 DETAIL VIEW A VIEW A VIEW A DETAIL VIEW B VIEW B VIEW B Version 1.1...
- Page 28 DETAIL VIEW C VIEW C Ice Master H-Series ®...
- Page 29 PARTS LIST ITEM NO. Part # DESCRIPTION QTY. CA3511221 8 inch lid CA300116 8 inch filter basket APD07G060PQB 7 GPM 60PSI, Bypass, 1/2" Quick Attach CSLC652 Pump Baseplate for IMS H-Series CSLC653 Plumbing Bracket for IMS H-Series CBLSTM07550 3/4 T-Strainer with Mesh Screen CVPBV234 3/4 FPT Union Valve CNST013...
- Page 30 PARTS LIST ITEM NO. Part # DESCRIPTION QTY. CBRN100-075 1 x 3/4 Poly Reducing Nipple RB075-050 .75-in x .5-in Reducer Bushing CV2241GXB100 Pressure gauge 100psi Glycerin filled CBM100G 1" Manifold Gasket CBFC100 1" Worm Screw Flange Clamp CFCW001 Clamp For 3/4" Hose CFCC003 Clamp for 1/2"...
- Page 31 IMSB7H - 7 NOZZLE BOOM FOR 3-POINT, 55 GAL. Version 1.1...
- Page 32 OVERVIEW Ice Master H-Series ®...
- Page 33 ITEM NO. Part # DESCRIPTION QTY. AZFPM005 IMS4-6 Stainless boom bracket AZFPM020 1" x 17-3/4" Poly Pipe For Deicing Boom AZFPM022 1" x 14-13/16" Poly Pipe For Deicing Boom AZFPM021 1" x 6-1/4" Poly Pipe For Deicing Boom CBCR100 1" Poly Pipe Cross CBEL10090 1"...
- Page 34 ITEM NO. PART # DESCRIPTION QTY. AMAH01GY HR030/050 REEL ONLY CFCC003 Clamp for 1/2" Hose CFPS01M02B 3/8 MPT X 1/2 HOSE BARB CFRB06 1/4-3/8 BSP FEMALE ELBOW CFRB07 STAINLESS PIPE 3/8 THREAD BOTH ENDS CFRB08 3/8 X 1/4 BALL BEARING SWIVEL CFRB09 1/4 MALE THREAD X 1/2 HOSE BARB CFRH03C...
- Page 35 ITEM NO. Part # DESCRIPTION QTY. AZKI009 Bracket for Tail Gate Mount Sprayer Rev.0 CHCS0920618 Steel Hitch Pin, 7/8" Dia x 4-1/4" Usable Length CV712HP .75 IN x 4.25 IN snap Lock Hitch Pin IMSHMB01 Version 1.1...
- Page 36 Watch Instruction Videos: www.youtube.com Discover More Helpful Tips: www.IceControlTraining.com Ice Master H-Series ®...
- Page 37 ACTIVATE YOUR 10-YEAR WARRANTY How to Activate To double your 5-year tank warranty, visit www.camionsystems.com/warranty/ and register this product. Watch Instruction Videos: www.youtube.com Discover More Helpful Tips: www.IceControlTraining.com Version 1.1...
- Page 38 ® CAMION by Enduraplas 1 (877) 265-9929 cs@camionsystems.com www.camionsystems.com 113 1st Street, Neche ND 58265, USA A Brand By Enduraplas Discover More Helpful Tips: www.IceControlTraining.com Copyright © Enduraplas. All Rights Reserved.