Advertisement
Quick Links
Advertisement
Related Manuals for rastar Ferrari SF1000
Summary of Contents for rastar Ferrari SF1000
- Page 1 97000 Ferrari SF1000 2.4GHz...
- Page 2 ATTENTIONS ATTENTIONS ● The guardian of child(ren) should read and understand the contents of this manual before using the product, and guide child(ren) to use the product properly. ● In order to avoid personal injury, using tools including knives to do assembly should be done by an adult.
- Page 3 TOOLS (NOT INCLUDED) Knife Tweezers Scissors Flat-nose pliers Components/ Assembly of Components ★Use flat-nose pliers to clip the compo- ★Peel off the sticker with tweezers and flatten it on the nent off, and then use knife to trim the component. interface part to be smooth.
- Page 4 (5)Gently press the sticker downwards until the bubbles disappear. COMPONENTS INSTALLED PROCEDURES FOR Ferrari SF1000 (1) Take all parts out and make sure nothing is missing. (2) Do not remove all the parts at first, but just do assembly step by step according to instruction of the manual.
- Page 5 B13-B24 C25-C39 A5-12 91600 40-43 【1】The item number of the applicable remote controller is 91600. 【2】There are numbers corresponding to each model, please do assembly based on the corresponding numbers according to instructions.
- Page 6 The following is a detailed tutorial and guidance on how to assemble stickers accessaries each part. Please pay attention to where there are icons on the right. Stickers on the corresponding position according to the serial number marked in the figures. Install B20 on 3.
- Page 7 Stickers on the corresponding position according to the serial number marked in the figures. (1) Install C34 on 1. (2) Install 3 on 1.
- Page 8 Stickers on the corresponding position according to the serial number marked in the figures. (1) Combine 42 with 43. (2) Install the combined 42 to 3. (3) Install 2 to 3.
- Page 9 Stickers on the corresponding position according to the serial number marked in the figures. Install A7 and A8 on 3.
- Page 10 Stickers on the corresponding position according to the serial number marked in the figures. (1) Install A9 and A10 on 3. (2) Install C35 on 3.
- Page 11 Stickers on the corresponding position according to the serial number marked in the figures. (1) Install C25 on 3. (2) Install A11 and A12 on 3. (3) Install 56 on 3. (4) Install C37 on 3.
- Page 12 (1) Install C29 on 3. (2) Install C26 on 3.
- Page 13 Install 6 pieces of 57 on the left and right sides of 3.
- Page 14 Stickers on the corresponding position according to the serial number marked in the figures. (1) Install C32 and C33 on 4. (2) Install B18 on 4.
- Page 15 (1) Install C38 on 4. (2) Install C30 and C31 on 4.
- Page 16 Install C27 and C28 on 4.
- Page 17 Install B14 and B15 on 4.
- Page 18 (1) Install 59 on 4. (2) Install B13 on 59.
- Page 19 Install B23 and B24 respectively to the corresponding positions of 4, align the holes with bolt 51 and then lock them.
- Page 20 Stickers on the corresponding position according to the serial number marked in the figures. (1) Install B17 on 4. (2) Install C36 on 4.
- Page 21 (1) Install 61 on 4 as shown in the figure. (2) Install 62 on 4 as shown in the figure.
- Page 22 Install 63 on 4 as shown in the figure, Pay attention to the correspondence between positive and negative poles.
- Page 23 (1) Install 60 on 4 as shown in the figure. (2) Install B16 on 4 as shown in the figure.
- Page 24 (1) Install C39 on A5. (2) Install A5 on 4.
- Page 25 Install B21 and B22 on 4.
-
Page 26: Front）（Rear
(1) Install front and rear wheels as shown in the figure.(when installing the front and rear wheels, please align the inside of the tire with the belt buckle, do not squeeze it) (2) Install the assembled front and rear wheels on 4. - Page 27 Please press the wire into the gap. Plug in respectively while matching by same colours and same shapes.
- Page 28 Combine the assembled models as shown in the figure.
- Page 29 (1) Install A6 on 4 as shown in the figure. (2) Put 3 pieces of 1.5V “AA” batteries into the car according to its polarity and then close the battery cover B19. (3) Twist C36 to lock the battery cover.
- Page 30 OPERATION GUIDE Flashing light of indicator Turn the switch to “ON” When indicator light on remote controller is off, the code matching is completed. ● Use a coin-like tool to twist the knob switch on battery cover to open or close it. Please refer to Figure ①. ●...
-
Page 31: Features And Functions
● Please turn off model car after playing. ● Adjust the direction adjustment switch to control the car running in a straight line. ● When battery of remote controller is low, the indicator light on remote controller will be dim, batteries need to be replaced. - Page 32 ATTENTION ● When your vehicle starts to lose power, it may lose its ● Do not operate your car on the streets where people gather or under high voltage functions or performance. This indicates that it's time to wires. Stay safe! refresh your batteries or recharge them.
-
Page 33: Maintenance
MAINTENANCE ● Remove the batteries when the unit is not in use for long periods of time. ● Clean the vehicle with a soft cloth. ● Avoid being heated or being exposed to strong sunlight. ● Keep dry. ● Regularly examine the toy for any damage to its wires, plug, enclosure and other parts and they must not be used until the damage has been repaired. - Page 34 BODY LOGO Put the stickers on the corresponding position according to the serial number. 42 36 32 46 62 48 50...
- Page 36 55 25 30 29 23 54 12...
- Page 38 Not for children under 3 years. used under adult supervision. The instruction has to be kept since it contains important information. Licensee: RASTAR (HK) INDUSTRIAL COMPANY LIMITED Produced under license of Ferrari S.p.A. The name FERRARI, the Manufacturer:RASTAR GROUP PRANCING HORSE device, all associated logos and distinctive Add:Xinghui Industrial Park, Xiadao Road, Shanghua, designs are property of Ferrari S.p.A.