1. Manuals
  2. Brands
  3. TriMark Manuals
  4. Door Opening System
  5. UM 34
  6. Instructions manual

TriMark UM 34 Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instructions and Proper Use
UM 34
Prevost H-Series Vehicle
Entry/Push to Start System
TriMark Corporation
500 Bailey Avenue
New Hampton, Iowa 50659
United States
www.trimarkcorp.com
TriMark
TriMark Corporation
08/22-1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UM 34 and is the answer not in the manual?

Questions and answers

Related Manuals for TriMark UM 34

Summary of Contents for TriMark UM 34

  • Page 1 Instructions and Proper Use UM 34 Prevost H-Series Vehicle Entry/Push to Start System TriMark Corporation 500 Bailey Avenue New Hampton, Iowa 50659 08/22-1 TriMark TriMark Corporation United States www.trimarkcorp.com...

  • Page 2: Table Of Contents

    Contents Introduction ..........................3 Push to Start ..........................3 Lock All ............................. 3 Lock Entry ..........................3 Unlock Entry/Unlatch ......................4 Unlock Luggage ..............................4 Lock and Unlock Confirmation ..........................4 e-FOB Operation and Features ....................4 Teaching Transmitter FOBs ............................5 32-Bit CAN Keypad Operation and Features ................. 5 Access Code ................................5 Authority Code ................................5 Locking doors with keypad ............................6...

  • Page 3: Introduction

    Introduction This manual provides the necessary information for the proper use of TriMark’s e-ASK System including module and keypad in the Prevost system. e-ASK module or controller 32-Bit CAN Keypad or Keypad Push to Start This vehicle is equipped with an advanced push to start ignition system. The start/ignition sequence is accomplished via CAN messaging between the Prevost Mux Module and the e- ASK module.

  • Page 4: Unlock Entry/Unlatch

    • If the entrance door is closed (J1P11=inactive or float) o Activates Wake Out (J1P10=GND for 1 second) o Attempts arming the alarm (see Alarm) o Locks entrance door by pulsing door Lock Relay (J1P5 +, J1P6 -) for ½ second o Sends CAN message to MUX for 2 seconds to lock the luggage doors Unlock Entry/Unlatch All the following methods will unlock the entry door:...

  • Page 5: Teaching Transmitter Fobs

    Teaching Transmitter FOBs The keypad is the only method of syncing fobs. The following sequence puts the e-ASK module into a “Fob Learn” mode. 1. Press 5/6 button on the keypad for 5 seconds, listen for double beep a. Keypad backlight continuously flashes on/off 2.

  • Page 6: Locking Doors With Keypad

    Locking doors with keypad Press and hold the (9/0) button for 1-2 seconds. An access code is not needed to lock the doors Keypad Secure Operations Entering a valid 4-digit access code enables secure operations. After entering an access code, the keypad is enabled for 5 seconds and a fifth button press and release initiates a secure operation.

  • Page 7: To Delete Access Codes

    To delete access codes 8. After the 3/4 key is pressed (step 3 above), if there are no access codes stored in memory, the keypad beeps for 2 seconds and returns to step 3 above. If there are stored codes, the keypad beeps twice. 9.

  • Page 8: Full Security Vs Reduced Security States

    • Entrance door is opened, door ajar input J1P11 is active (grounded) • Entrance door is unlocked, Entrance door key switch J1P8 is active (grounded) The Prevost Mux system is configured at the time of delivery with the following options related to the Alarm: (Prevost Field service personnel can re-configure).

  • Page 9: Replacing The 32-Bit Can Keypad

    Panic is disabled by pressing any fob button (other than the Panic button) or unlocking the entrance door via the keypad. Replacing the 32-Bit CAN Keypad For improved security/theft prevention, the keypads and e-ASK controllers are paired at the factory to prevent swap-out violations. If the keypad is changed, the keypad will play a 2 second error beep.

  • Page 10: Keypad Status Led's And Backlighting

    CAN Address Conflict EEPROM Read/Write Error Keypad Status LED’s and Backlighting The Keypad back lighting is typically off. When a button is pressed, the backlight illuminates momentarily. After button presses stop, the backlight is low for 30 seconds. After 30 seconds of no keypad activity the keypad back lights turn off again.

  • Page 11: Connectors And Pinouts

    One particular e-FOB function does Check wire connection of affected function at RF module, not work wiring harness, and e-ASK module. 32-Bit CAN Keypad Hints Verify power and ground connections to the Keypad. No response with button press Verify that keypad cable is connected. (rest of system will function).

  • Page 12: Regulatory Information

    ENTRANCE UNLOCK OUTPUT (15A) INTERIOR LOCK SWITCH INPUT (-) VEHICLE POWER (+12V DC) 12V ANTI-THEFT LED SUPPLY DOOR KEY SWITCH INPUT (-) ANTI-THEFT LED OUTPUT (-500 mA) UNUSED OUTPUT (-500 mA) INTERIOR SWITCH UNLOCK INPUT (-) WAKE OUTPUT (-500 mA) ENTRANCE DOOR UNLATCH OUTPUT (-500 mA) DOOR AJAR INPUT (-) UNUSED LF ANTENNA 3 RETURN...

  • Page 13: Rf Exposure Statement

    émetteur Note: No part of this publication may be copied, modified, revised, reproduced, distributed, reused, transmitted to a third party, or translated in any language without the prior written permission of TriMark Corporation.

Table of Contents