Subscribe to Our Youtube Channel
Related Manuals for Bestway SALUSPA S100105
Summary of Contents for Bestway SALUSPA S100105
- Page 2 OWNER’S MANUAL S100105/S100205 WE SUGGEST NOT TO RETURN THE PRODUCT TO THE STORE QUESTIONS? PROBLEMS? MISSING PARTS? Visit the Bestway YouTube channel For FAQ, Manuals, Videos Or spare Parts, Please Visit bestwayusa.com/support CONTENTS IMPORTANT SAFETY INSTRUCTIONS PG 002 PRE-SETUP PG 009...
- Page 3 WARNING IMPORTANT SAFETY INSTRUCTIONS When using this electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL INSTRUCTIONS. WARNING – To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times. A wire connector is provided on this unit to connect a minimum 8 AWG (8.37 mm solid copper conductor between this unit and any metal equipment, metal enclosures of electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the unit.
- Page 4 CAUTION: Immediately leave spa if the user feels uncomfortable or sleepy. NOTE: Please examine equipment before use. Notify Bestway at the customer ® service address listed on this manual for any damaged or missing parts at the time of purchase.
- Page 5 The warning label must be posted near your spa in a readable position during using your spa. 1. Take out the warning label from the accessory kit. 2. Carefully peel the warning label. 3. Affix the warning label. To order the warning label, please contact your local Bestway After Sales Service.
- Page 6 Model Number : S100105 / S100205 Trade Name : Bestway Responsible Party in USA : Bestway (USA) Inc. 3435 S. McQueen Road, Chandler, AZ 85286, United States of America Testing Laboratory : Intertek Testing Services Shanghai Building No.86, 1198 Qinzhou Road (North),Caohejing...
- Page 7 SPA SUCTION FITTING INSTRUCTIONS When installing and using this equipment, basic safety precautions shall always be followed, including the following: IMPORTANT SAFETY INSTRUCTIONS READ, FOLLOW, AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS. • Any modification that increases the flow rate of the circulation system shall require re-evaluation of the cover/grate and sump to ensure that the flow rating of the Suction Outlet Fitting Assembly (SOFA) is not exceeded.
- Page 8 • Cover/grates, when installed, shall not protrude more than 2 in. (51 mm) from the finished surface of the pool in which the SOFA is installed. Installation Information label (Copy) Manufacturers name: Bestway (Nantong) Recreation Corp. Cover part number: S01 Life expectancy: 3 Years...
- Page 9 PRE-SETUP CHECK LIST To check the parts printed on the package, verify that the equipment components represent the model that you had intended to purchase. In case of any damaged or missing parts at the time of purchase, visit our website bestwayusa.com/support.
- Page 10 • The selected position must be far from the house entrance. Do not position any equipment or other furniture around the spa. The water that comes out of the spa during the use or due to a faulty product can damage the furniture inside the house or surrounding the pool.
- Page 11 long periods of time. We recommend protecting the spa from direct sun light exposure by a cover when not in use. Follow the important instructions above to choose the correct surface and location to set up your spa. Damaged parts of the spa, due to the fact that the set-up surface and location does not match the instructions, will not be considered as manufacture defect and will avoid the warranty and any...
- Page 12 INSTALLATION For the installation instructions, follow the drawings printed on the package. Drawings are for illustration purposes only. May not reflect actual product. Not to scale. RECOMMENDATIONS DURING THE INSTALLATION • Keep the spa away from the rest area to minimize noise disturbance. •...
- Page 13 TEMPERATURE ADJUSTMENT BUTTONS: Pressing the button, the display starts to flash showing the set temperature for 3 seconds, after that it will show again to the real water temperature. When it is flashing you can adjust the temperature using the button.
- Page 14 MAINTENANCE CAUTION: You must ensure the pump is unplugged before beginning spa maintenance to avoid risk of injury or death. LINER • It is normal that your spa liner may appear as if it is losing air. Changes in ambient temperature may change the internal air pressure in the liner. •...
- Page 15 TROUBLESHOOTING Problems Probable Causes Solutions Pump does not operate - Power failure - Check power source - Power circuits is broken - For assistance, please visit the support section on our website, www.bestwayusa.com Pump does not - Temperature set too low - Set spa to a higher temperature;...
- Page 16 ONLY FOR SPA EQUIPPED WITH Wi-Fi Problems Probable Causes Solutions The pump has been connected to the If the router your pump is connected to is dual-band and currently not wrong band connecting to a 2.4GHz network, please switch to another band of the same router (2.4GHz) and try to pair pump heater again.
- Page 17 ERROR CODES CAUSES REASONS SOLUTIONS The water flow sensors work 1. The water flow sensor flags didn’t fall back into the 1. Unplug the plug gently, strike the side of the pump but not violently, and plug it without pressing the filter or heat correct position.
- Page 19 A: 1.
- Page 20 Exported by Bestway (Hong Kong) International Ltd./Bestway Enterprise Company Limited Suite 713, 7/Floor, East Wing, Tsim Sha Tsui Centre, 66 Mody Road, Kowloon, Hong Kong Distributed in North America by Bestway (USA) Inc., 3435 S. McQueen Road, Chandler, AZ 85286, United States of America Tel: +86 21 69135588 www.bestwayusa.com...
Need help?
Do you have a question about the SALUSPA S100105 and is the answer not in the manual?
Questions and answers
Can the heater still work if the lock is on?
Yes, the heater can work when the control panel is locked. The lock only prevents panel operation but does not stop active functions like heating.
This answer is automatically generated
Are there debris screens in the main pump lines?
Yes, the Bestway SALUSPA S100105 has debris screens in the main pump lines.
This answer is automatically generated
How do I hook up pump
To hook up the Bestway S100105 pump:
1. Ensure the pump adapters are at the same level as the hot tub adapters. If not, elevate the pump using wood or another insulated material.
2. Check that seals are present and correctly positioned inside the pump adapters to prevent leaks.
3. Insert stopper caps on the spa ports before disconnecting or connecting the pump.
4. Make sure the pump is properly connected to the spa adapters.
5. Plug in the pump and test the ground-fault circuit interrupter (GFCI) by pressing the test button, then the reset button to ensure safe operation.
Refer to the manual for detailed diagrams and safety guidelines.
This answer is automatically generated
brand new pump comes up flashing 6cf want let me do anything thing
When the Bestway pump S100105 shows a flashing 6cf error and is unresponsive, it indicates a water flow issue. Possible causes include:
- The water pump is broken if no water flows out from the outlet pipe inside the pool.
- The water flow sensors are broken if water flows out but the alarm still appears.
- The filter is blocked and needs cleaning, checking for damage, or replacement.
- The pipes in the liner are bent, causing poor water flow.
- The debris screens are blocked by hard water deposits like calcium build-up and need cleaning.
This answer is automatically generated
I have an E01 error code indicating a failed water flow sensor. I need the part number for the water sensor on model s100105.