Table of Contents
Related Manuals for FIXATOR LM90A
Summary of Contents for FIXATOR LM90A
- Page 1 Réf : 1813000156 INSTRUCTION MANUAL Page : 1/17 Electrical winches LM90A/LM250A Version : 23/21 INSTALLATION – USE MAINTENANCE Monitoring of updates Date Description 08th Jun 2021 New format - type A for Radio option (modification 1300)
-
Page 2: Table Of Contents
The original of this document is in French. No translation can replace the original. Thank you for purchasing a FIXATOR product. In the following pages we give you details of instructions allowing you to safely use and maintain your equipment in good working condition. Please read these instructions prior to commissioning the equipment: no installation operation, use and maintenance should be performed until this document has been fully understood. -
Page 3: Generalities
(check has a special profile, and in which the cable is tight instructions on the hoist plate: "Type LM90A" or “LM250A”). under the effect of the load by two articulated rollers. This allows an unlimited run of the hoisting cable. -
Page 4: Specifications
Réf : 1813000156 INSTRUCTION MANUAL Page : 4/17 Electrical winches LM90A/LM250A Version : 23/21 A test prior to initial commissioning and after each maintenance or dismantle must be performed with a Specifications static test coefficient of 1.25xWLL and a dynamic The LM winch has a working load limit (WLL) test coefficient of 1.1xWLL. -
Page 5: Anchoring
Anchoring Verify that the anchoring point is strong enough for the effort to apply. If the anchoring is not provided by FIXATOR each anchor must withstand, without any deformation, up to 2.5 times the WLL of the winch, that is 2.5x90=225 kg (respectively 2.5x250=625 kg for a... -
Page 6: Installation And Use
Réf : 1813000156 INSTRUCTION MANUAL Page : 6/17 Electrical winches LM90A/LM250A Version : 23/21 bottom of hook. The pawl 2 Installation and Use of safety of the hook must close completely. Instructions for installation, assembly, commissioning and use - training Les opérations d’installation et d’utilisation doivent... -
Page 7: Reeving For Lifting Of Load
Réf : 1813000156 INSTRUCTION MANUAL Page : 7/17 Electrical winches LM90A/LM250A Version : 23/21 In case of reeving, double the maximum load to be taken into account for the calculations of security. NOTA : take care to mount the pulley block so that its limit spring is located on the cable between the pulley and the entry in the hoist (see figure). -
Page 8: Power
Réf : 1813000156 INSTRUCTION MANUAL Page : 8/17 Electrical winches LM90A/LM250A Version : 23/21 Stop immediately if the loose strand comes to tangle with the other strands. 2.1.4 Power The installer must ensure that the power supply is compatible with the specification of the winch. -
Page 9: Diagrams And Safety Explanations
2.2.1 Main dimensions Check the operation of the limit switches of the winch. For your safety, use only FIXATOR cables. Ensure that the cable above the hoist (taut) does not touch surfaces or angles. Ensure that the outgoing winch cable (slack) is free. -
Page 10: Safety Devices
Réf : 1813000156 INSTRUCTION MANUAL Page : 10/17 Electrical winches LM90A/LM250A Version : 23/21 2.2.2 Safety devices Normal use - A main brake acts on the engine in case of This hoist is designed for lifting loads. power supply failure... -
Page 11: Residual Risks
For the hoist LM Never disable the safety features. type LM90A, the ranking is A2. type LM250A, the ranking is A1. Never swing a load voluntarily. In some countries, periodic audits and reviews of Do not block a control. -
Page 12: Adjusting Of The Brake
If necessary, it is possible to unlock the brake manually, by pressing the (8) pivot. After each operation, a load test must be performed. FIXATOR or its dealers can train your staff for the maintenance of your winches. For your safety and to benefit from the full... -
Page 13: Troubleshooting
The groove pulley is worn or dirty Verification The brake is worn Adjust the brake The adhesion system is worn or dirty Verification Note and send the information listed on the plate shown below before requesting parts. Spare parts Use only FIXATOR original spare parts. -
Page 14: Disposal
Réf : 1813000156 INSTRUCTION MANUAL Page : 14/17 Electrical winches LM90A/LM250A Version : 23/21 Capacitor 40uF ref 540582 Pendant control ref 461020 Motor cap ref 540601 Fuse ref 244612 Disposal Disassembly and disposal of the hoist must be in accordance with the current regulations in force. - Page 15 Réf : 1813000156 INSTRUCTION MANUAL Page : 15/17 Electrical winches LM90A/LM250A Version : 23/21...
-
Page 16: Optionnal Radio Remote Control
Réf : 1813000156 INSTRUCTION MANUAL Page : 16/17 Electrical winches LM90A/LM250A Version : 23/21 - Press the 2 START buttons simultaneously for 1 Optionnal radio remote control sec. - Release; The lower LED goes out. A remote control is regarded as a control device;... - Page 17 Réf : 1813000156 INSTRUCTION MANUAL Page : 17/17 Electrical winches LM90A/LM250A Version : 23/21 The original of this document is in French, no translation can replace it. P.A. 8, rue du Bois Rinier - B.P. 10041 – 49181 ST BARTHELEMY D’ANJOU (France) TEL : + 33 (0) 2 41 31 17 00 –...