Advertisement
Quick Links
M1 除泡机
M1 Bubble Remover Machine
用户使用说明书
Operating Instruction
1.安全守则---------------------------------
1.Safety Rule
2.参数规格---------------------------------
2.Specification
3.设备特点---------------------------------
3.Features
4.设备安装 -------------------------------
4. Installation
5.操作流程---------------------------------
5.Operation
6.保养流程---------------------------------
6.Maintenance
Advertisement
Related Manuals for M-Triangel M1
Summary of Contents for M-Triangel M1
- Page 1 M1 除泡机 M1 Bubble Remover Machine 用户使用说明书 Operating Instruction 1.安全守则--------------------------------- 1.Safety Rule 2.参数规格--------------------------------- 2.Specification 3.设备特点--------------------------------- 3.Features 4.设备安装 ------------------------------- 4. Installation 5.操作流程--------------------------------- 5.Operation 6.保养流程--------------------------------- 6.Maintenance...
- Page 2 1.安全守则 1.Safety Rule 为了您的个人安全，仔细阅读本手册。熟知机器的应用与限制，以及与机 器相关的潜在性危险。 For your own safety, please read this manual carefully. Please familiar with the application and limitation of the machine, as well as the relevant potential risk. A. 请在使用设备前仔细阅读说明书。 A.Please read this manual carefully before using the machine. B.
- Page 3 Equipment Power：300W 建议使用不低于 2 升的空压机 It is recommended that use a vacuum pump who not less than 2 liters 3.设备特点 Features 1.7 寸，体积小，超薄除泡机，功能强大。 1. 7inch， small size, ultra-thin in addition to foam machine, powerful. 2.除泡时间短，30 秒一片 2. High efficient , 30 seconds per piece 3 .设备高智能化，一键全自动运行...
- Page 4 2.给空压机装上消音器 2. Install the muffler on the air compressor (1)顶部红色按钮按下是关掉，往上空压机启动。 （1）Press the top red button is turned off, up is start up. (2)右侧开关阀，竖着是抽气，横着是放气。 （2）The right side is open valve, vertical is pumping, sideways is deflated. 5.操作流程 5.Operation...
- Page 5 1.参数设置 2.1.Check setting on the screen 查看液晶屏上的参数，出厂默认参数为除泡温度：40℃，除泡时间：30 秒 Laminating temperature: 40℃; Vacuum time: 30s; Laminating time: 30s; Defoaming temperature: 40℃. *没有特殊要求，请勿擅自调试参数，如需更改参数，请联系厂家售后。 .*Attention: This is factory settings, please don’t adjust it by yourself. 2.把屏幕放入仓门，排线放在下方。 2.Put the screen into the door, the cable on the bottom...
- Page 6 3.按下启动键，30 秒左右，即可按下停止键，拿出屏幕。 3.3. Press the start button, about 30 seconds, you can press the stop button, take out the screen. 注意：建议翻排线后压屏 Attention: Press the screen after turn the cable 6.设备保养 Maintenance 保养项目 保养注意事项 Items Notes 平台和压板 检查是否有杂物，如有请及时清理。 Platform and platen Keep clean, no clutter inside.