Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for EMTOP SBC-IMX8MM
Summary of Contents for EMTOP SBC-IMX8MM
- Page 1 SBC-IMX8MM Quick Operation Guide EMTOP Technology Co.,Ltd. www.emtop-tech.com...
-
Page 2: Table Of Contents
1. Setting Up HyperTerminal....................2 2. Hardware Connects......................6 Linux Operating System.......................8 1. Create System TF Card....................8 2. Update of TF Card System Image................9 3. Update eMMC........................ 10 Technical Support and Warranty..................... 11 Copyright © 2017 Emtop Technology SBC-IMX8MM Quick Operation Guide... -
Page 3: Product Overview
HDMI by default; If another display mode is required, please refer to the Display Mode Configurations in user manual. SBC-IMX8MM has no CR1220 battery installed on board; Please purchase it if necessary. SBC-IMX8MM Single Board Computer preferably boots from EMMC by default, if ... -
Page 4: Preparations
EMTOP TECHNOLOGY Preparations 1. Setting Up HyperTerminal 1） Click Start > Programs > Accessories > Communications > HyperTerminal on your PC’s desktop; Figure 1 Start HyperTerminal Copyright © 2017 Emtop Technology SBC-IMX8MM Quick Operation Guide... - Page 5 2） Enter a name in the Name field and select an icon below, and then click OK; Figure 2 Enter a Name 3） Select the port to be used and click OK; Figure 3 Select Port Copyright © 2017 Emtop Technology SBC-IMX8MM Quick Operation Guide...
- Page 6 EMTOP TECHNOLOGY 4） Please configure the port you selected as shown in the following window, and then click OK; Figure 4 Configure Port Copyright © 2017 Emtop Technology SBC-IMX8MM Quick Operation Guide...
- Page 7 EMTOP TECHNOLOGY 5） HyperTerminal has been set up successfully. Figure 5 HyperTerminal Window Copyright © 2017 Emtop Technology SBC-IMX8MM Quick Operation Guide...
-
Page 8: Hardware Connects
Table 1 Connection Details Descriptions Descriptions Connect Serial Cable Connect a Power Adapter If you want to boot from TF card, Connect HDMI Adapter Board Need Press boot button before Power Up Copyright © 2017 Emtop Technology SBC-IMX8MM Quick Operation Guide... - Page 9 EMTOP TECHNOLOGY Copyright © 2017 Emtop Technology SBC-IMX8MM Quick Operation Guide...
-
Page 10: Linux Operating System
Note: It is not recommended to use other versions of HP USB Disk Storage Format Tool. HP USB Disk Storage Format Tool will erase the partitions of TF card. Copyright © 2017 Emtop Technology SBC-IMX8MM Quick Operation Guide... -
Page 11: Update Of Tf Card System Image
TF Card under Ubuntu, change the target file and umount the Card. Note: Press down the button "BOOT" before power up, don't release it. Wait until booting message shows on the terminal [3 seconds at most], release the button. Copyright © 2017 Emtop Technology SBC-IMX8MM Quick Operation Guide... -
Page 12: Update Emmc
root@imx8mmddr4evk:~# dd if=/run/media/sda1/imx-image-full-imx8mmddr4evk- xxx.img of=/dev/mmcblk2 After it's done, power off the board, remove the TFCard, then reboot the board, it should boot from eMMC and enter into Linux prompt. Copyright © 2017 Emtop Technology SBC-IMX8MM Quick Operation Guide... -
Page 13: Technical Support And Warranty
1） 12-month free warranty on the PCB under normal conditions of use since the sales of the product; 2） The following conditions are not covered by free services; Emtop Technology will Copyright © 2017 Emtop Technology SBC-IMX8MM Quick Operation Guide... - Page 14 4） Please contact technical support if there is any repair request. Note: Emtop Technology will not take any responsibility on the products sent back without the permission of the company. Contact Information Copyright © 2017 Emtop Technology...
- Page 15 EMTOP TECHNOLOGY Technical Support Tel: +86-0755-23742193 Email: support@emtop-tech.com Sales Information Email: sales@emtop-tech.com Company Information Website: www.emtop-tech.com Copyright © 2017 Emtop Technology SBC-IMX8MM Quick Operation Guide...
Need help?
Do you have a question about the SBC-IMX8MM and is the answer not in the manual?
Questions and answers