Subscribe to Our Youtube Channel
Related Manuals for RuoShui 01+
Summary of Contents for RuoShui 01+
- Page 1 TEMPERATURE CALIBRATOR OPERATION MANUAL RuoShui 01+ 이 자료는 저작권법에 따라 보호받는 저작물이므로 무단배포 및 무단복제를 금하며, 내용을 이용하려면, 한국 VictorRuoshui 社 의 서면동의를 받아야 합니다.
-
Page 2: Section One -Safety Statement
www.victorruoshui.co.kr • To ensure accuracy, preheat for 5 minutes after Section One -Safety Statement power-on. To ensure safe use, the meter and manual employ • Please contact the manufacture or dealers if the the following symbols: Users have higher accuracy requirement. Warning identifies conditions and actions that Section Two - Panel Introduction may pose hazard(s) to the user and... - Page 3 www.victorruoshui.co.kr Illustration for LCD display display part range selection power-on OUTPUT : indicates the meter is in output function ℃/℉ shift state. : indicates the meter is in calibration state. thermocou output cold clearing 0 FS : indicates the present calibrated compensat zero point or full point etc.
-
Page 4: Section Three- Maintenance
www.victorruoshui.co.kr Warning :indicates connection of To avoid electrical shock or personal injury: output signals. Remove test leads from the meter before Pt10, Pt100, Pt200, Pt500, Cu50, Cu10 : opening the battery door. indicates graduated thermal Close and latch the battery door before using resistance(RTD). -
Page 5: Section Five-Output Of The Meter
www.victorruoshui.co.kr (2) Automatically turn off the power The default factory value is set as: the meter will automatically turn off if no operation has been made within 15 minutes. The Users can set by themselves to choose whether using this function or not (See Section Six). Section Five-Output of the Meter The meter generates DC current or simulate resistance set by the Users from the corresponding... - Page 6 www.victorruoshui.co.kr Press 〔〕/〔〕key, select output set bit; Press 〔〕/〔〕key , change the value of set bit, and the value can carry or abdicate automatically, and hold the key, the value will change constantly after one second. Automatic compensation of cold junctions When calibrating meter with temperature cold junction compensation directly, press 〔RJ-ON〕key to start the automatic compensation function of cold...
- Page 7 www.victorruoshui.co.kr two wires connection method; The meter may 0000.0C(other graduation). Press 〔℃/℉〕 key , select Centigrade or Fahrenheit generate incorrect resistance value if the capacity between the output terminals and the unit. measured meter is higher than 0.1 uf. (3) Resistance or thermal resistance(RTD)simulate output Note ·...
-
Page 8: Section Six- Function Setting
www.victorruoshui.co.kr in output state Press 〔FUN〕key , select resistance or thermal Section Six- Function Setting resistance (RTD) function, and display „‟ or „C‟ and thermal resistance „Pt100‟ graduation no.; The following operation can change the automatic power off function of the meter: thermal resistance (RTD) - Page 9 www.victorruoshui.co.kr -40~1760C 1C Employs ITS-90 0.05%+3C (≤100C) temperature standard 0.05%+2C (> 100C) -20~1760C 1C Note 3 0.05%+3C (400~600C) 400~1800C 1C 0.05%+2C (> 600C) -200.0~1000.0C 0.1C -200.0~1370C 0.1C 0.05%+2C (≤ -100C) -200.0~1200.0C 0.1C 0.05%+1C (> -100C) -200.0～400.0C 0.1C -200.0～1300.0C 0.1C Cu10 -10.0C~250.0C 0.1C 0.05%+0.6C...
- Page 10 www.victorruoshui.co.kr Note 1：Affiliated resistance of test lead is excluded Note 2：The range of incentive current is from 0.05mA to 3mA, and the maximum output is less than or equals to 2V Note 3：The accuracy does not include the error of interior temperature compensation sensor the range of interior temperature compensation sensor is from -10 to 50C, and the error compensation is less than or equals to 0.
- Page 11 www.victorruoshui.co.kr The present operation instruction is subject to change without notice; The content of the operation instruction is regarded as correct. Whenever any user finds its mistakes, omission, etc., he or she is requested to contact the manufacturer; ...
-
Page 12: Warranty
www.victorruoshui.co.kr FA2—E100065 / VER（0.0）/ NUM（1/1） WARRANTY Our company warrants to the original purchaser that each product it manufactures will be free from defects in material and workmanship under normal use and service for a period of one year from date of purchase. Our company‟s warranty does not apply to fuses, test leads or any product which, in our company‟... - Page 13 www.victorruoshui.co.kr least four inches of excelsior or similar shock-absorbing material. CLAIM FOR DAMAGE IN SHIPMENT TO ORIGINAL PURCHASER The instrument should be thoroughly inspected immediately upon original delivery to purchaser. All material in the container should be checked against the enclosed packing list. The manufacturer will not be responsible for shortages against the packing sheet unless notified immediately.
- Page 14 www.victorruoshui.co.kr INDEX P a g e Safety Information………………………………………………………………………………………………………… 1 Instrument Panel Layout and Functions……………………………………………………………………………… 2 Instrument Maintenance………………………………………………………………………………………………… 3 Power-on/off of Instrument……………………………………………………………………………………………… 4 Output from Instrument……………………………………………………………………………………………………4 Setting Function………………………………………………………………………………………………………… 7 Performance Index……………………………………………………………………………………………………… 7 Notice of the Manual………………………………………………………………………………………………………10 이 자료는 저작권법에 따라 보호받는 저작물이므로 무단배포 및 무단복제를 금하며, 내용을 이용하려면, 한국 VictorRuoshui 社...
Need help?
Do you have a question about the 01+ and is the answer not in the manual?
Questions and answers