Related Manuals for LAUNDRY JET Plus
Summary of Contents for LAUNDRY JET Plus
- Page 1 NSTALLATION UIDE Laundry Jet Plus April 2022 Version 4.0 Revision 0.1 Rev 8 Units for Use with ISense Ports Laundry Jet 2001 Challenger Avenue Oroville, CA 95965 +1.800.867.4580 sales@laundryjet.com www.laundryjet.com...
- Page 2 INSTALLATION GUIDE +1.800.867.4580 sales@laundryjet.com www.laundryjet.com...
- Page 3 Version Date Document Changes Number 4/12/2017 1.0 Rev 0.1 Plus Jet Pack Installation Guide - Rev 3 Units 7/21/2017 1.0 Rev 0.2 Plus Jet Pack Installation Guide - Rev 3 Units 5/4/2020 2.1 Rev 1.0 Plus Jet Pack Installation Guide - Rev 4 Units 6/17/2021 2.1 Rev 2.0...
-
Page 4: Table Of Contents
3 - Components & Tools 3.1 - Pipe Installation Standards 3.2 - Port Drop Installation 3.3 - Port 90 Installation 3.4 - Plus Jet Pack Pipe Drop ISense Port Installation 12-15 4 - Components & Tools 4.1 - Port 90 Mount Bracket 4.2 - ISense Sheetrock Template... -
Page 5: Introduction
Vacuum Laundry Pipe Laundry Jet specifies 6" SDR35 White Solvent Weld PVC pipe and fittings. This piping is light weight to make install quick and easy. PVC piping is designed to have a smooth transition in between fittings and connections which ensures that clothing, bedding and towels will travel smoothly to the laundry room. -
Page 6: Contents
Contents 2 Contents Laundry Jet Plus Jet Pack ISense Port Pipe Components All Fittings are 6" SDR35 White Solvent Weld 6 Inch Wye 6 Inch 45° Elbow 6 Inch Coupler 6 Inch Cleanout 6 Inch 90° 6 Inch Swept 90°... -
Page 7: Pipe Installation Overview
Pipe Installation 3 Pipe Installation Overview Components Port 90 Assembly 6 Inch Wye 6 Inch Cleanout Adapter 6 Inch 45° Elbow ISense Sheetrock Template Cable Bundle Tools Cordless Drill Sawzall Tape Measure Clear 2 Part PVC Glue 1" Wood Screw Plumber's Metal Strapping Tape +1.800.867.4580 sales@laundryjet.com... -
Page 8: Pipe Installation Standards
Pipe Installation 3.1 Pipe Installation Overview Pipe Installation Standards Required Piping Installation Standards All joints must use a minimum entry angle of 45 degrees with a break distance of 18 Inches (460 MM). See Image below. Pipe cuts must be straight and de burred before seating. ... -
Page 9: Port Drop Installation
Port Drop Installation 3.2 Pipe Installation Overview Port Drop Installation Mount port 90 using the Port 90 Mount Bracket. See Page 11 for Port 90 Installation. Use a standard SDR 6" Swept 90 for your Port Drop Installation. Block and strap drop line at midway point +1.800.867.4580 sales@laundryjet.com... -
Page 10: Port 90 Installation
Port 90 Installation 3.3 Pipe Installation Overview Port 90 Installation Port 90 must be installed with front face of Port 90 flush with the finished face of ▪ interior wall. Port 90 must be installed on a plum horizontal port drop line. ▪... -
Page 11: Plus Jet Pack Pipe Drop
Jet Pack Pipe Drop 3.4 Pipe Installation Overview Plus Jet Pack Pipe Drop Install a standard swept 90 drop to each port using a swept 90 elbow. Strap pipe at attic to ceiling transition. +1.800.867.4580 sales@laundryjet.com www.laundryjet.com... -
Page 12: Isense Port Installation
ISense Port Installation 4 ISense Port Installation Components Port 90 ISense Port ISense Sheetrock Template Pipe Mount Bracket 1" Wood Screw Tools Stud Finder Sawzall Screw Driver +1.800.867.4580 sales@laundryjet.com www.laundryjet.com... -
Page 13: Port 90 Mount Bracket
ISense Port Installation Step 1 - Port 90 Mount Bracket Port 90 Mount Bracket Use the Port 90 Mount Bracket to align and secure the Port 90 to the frame Set Port height Attach 2 pipe clamps Set elevation screws ... -
Page 14: Isense Sheetrock Template
ISense Port Installation 4.2 Step 2 - ISense Sheetrock Template Sheetrock Template Install sheetrock over the Port 90 Mount Bracket ▪ Trim around outside edge of the Port 90 and remove material ▪ Position the round portion on the back of the template into the Port 90 ▪... -
Page 15: Isense Port Installation
ISense Port Installation Step 3 - ISense Port Assembly ISense Port Assembly Connect RJ45 male connector to female connector on back of port ▪ Remove the front logo plate and position the Port into place ▪ Align Port for final adjustment using a level ▪... -
Page 16: Plus Jet Pack Installation
Plus Jet Pack Installation 5 Plus Jet Pack Installation Components Plus Jet Pack Housing Plus Jet Pack Front Panel Plus Jet Pack Blower Pod 4" Square Connector Tools Cordless Drill Stud Finder Level +1.800.867.4580 sales@laundryjet.com www.laundryjet.com... -
Page 17: Jet Pack Installation
Remove the ten 10-32 screws from the left side of the unit and remove temporary cardboard/wooden stabilizing plate. ▪ Using a flathead screw driver, carefully remove the two left side magnetic cover plates. Remove the two 1/4-20 screws and the twelve 6-32 screws. Remove the front panel of the Plus Unit. +1.800.867.4580 sales@laundryjet.com www.laundryjet.com... - Page 18 Plus Jet Pack Installation 5.2 Plus Jet Pack Installation Blower Pod Installation ▪ Align and position the blower pod between guide rails and slide into the unit until fully seated. Reinstall the ten 10-32 screws. ▪ Install the 4" Square Connector thru the square cutout in the unit, and into the square flange of the Blower Pod.
- Page 19 Plus Jet Pack Installation 5.3 Plus Jet Pack Installation Step 1 Modify the Custom cabinet to accommodate the Plus Cabinet. Using the provided drawings in Section 7, use appropriate tooling to remove the necessary material from the cabinet. +1.800.867.4580 sales@laundryjet.com...
- Page 20 Plus Jet Pack Installation 5.4 Plus Jet Pack Installation Step 2 If possible, provide the Installation spec to the cabinet maker ahead of build. Please reference Section 7 for Engineering Prints. +1.800.867.4580 sales@laundryjet.com www.laundryjet.com...
- Page 21 Plus Jet Pack Installation 5.5 Plus Jet Pack Installation Step 3 Locate the Plus Cabinet into the custom cabinet with the Plus Cabinet oriented to the right until it sits flush with the right side face of the custom cabinet.
- Page 22 5.6 Plus Jet Pack Installation Step 4 Using a level ensure that the Plus Cabinet is level and to the back and right of the cabinet. In 4 places using provided hardware, set the 4 set screws that fix the right face of the Plus Cabinet to the custom cabinet.
- Page 23 Plus Jet Pack Installation 5.7 Plus Jet Pack Installation Step 5 Set 2 set screws through the back wall of the Plus Cabinet into the custom cabinet. +1.800.867.4580 sales@laundryjet.com www.laundryjet.com...
- Page 24 Plus Jet Pack Installation 5.8 Plus Jet Pack Installation 110 v Outlet Step 6 Cut out a section of 6" SDR 35 pipe so that it sits either flush or above the top of the cabinet or extends through the ceiling. Use a window sealer to seal between the pipe penetration and the custom cabinet.
- Page 25 Plus Jet Pack Installation 5.9 Plus Jet Pack Installation Step 7 Connect the trunk line to the Vac Chamber flange. Bond in place ensuring a tight supply seal. +1.800.867.4580 sales@laundryjet.com www.laundryjet.com...
- Page 26 Plus Jet Pack Installation 5.10 Plus Jet Pack Installation Step 8 Attach main front panel. Prior to attaching the panel, make sure the seal material is in good shape and has not been pulled off or torn during the installation process. Attach panel using the provided hardware.
- Page 27 Open & close cabinet doors to make sure they have adequate clearance to open and close freely. There is no need for a seal here as the Plus Cabinet is a sealed system. +1.800.867.4580 sales@laundryjet.com...
- Page 28 Plus Jet Pack Installation 5.12 Plus Jet Pack Installation Step 10 Test all RJ45 connections prior to the next step (T568B) Ensure that the Jet Pack is not plugged in. Connect all the RJ45 cables as shown above.
-
Page 29: Warranty
6 Warranty Lifetime Limited Warranty Laundry Jet is protected by a 3 year limited lifetime warranty. This warranty is valid from the date of purchase, for as long as you are the original owner, the system remains at its original... -
Page 30: Engineering Prints
+1.800.867.4580 sales@laundryjet.com www.laundryjet.com... - Page 31 +1.800.867.4580 sales@laundryjet.com www.laundryjet.com...
- Page 32 +1.800.867.4580 sales@laundryjet.com www.laundryjet.com...
- Page 33 +1.800.867.4580 sales@laundryjet.com www.laundryjet.com...
Need help?
Do you have a question about the Plus and is the answer not in the manual?
Questions and answers