Troubleshooting; Specifications; Legal Notices - Insignia NS-R2001 User Manual

NS-R2001_10-1254_MAN_ENG.book Page 12 Friday, February 11, 2011 7:43 AM

Troubleshooting

If a problem occurs, run through the table below
before contacting Insignia.
If the problem persists, attempt to solve it by
switching the receiver off and on again. If this fails
to resolve the problem, contact Insignia. Under no
circumstances should you attempt to repair the
receiver yourself as this could void the warranty.
Category Problem
No power
• The AC power cord is
disconnected.
• Poor connection at AC
wall outlet or the outlet
is inactive.
No sound
• The speaker cords are
disconnected.
• The volume is adjusted
too low.
• The MUTE button on the
remote control is pressed
to ON.
• Speakers are not
switched on.
• Incorrect selection of the
input source.
• Incorrect connections
between the
components.
Stations cannot
• No antenna is connected.
be received
• The desired station
frequency is not tuned in.
• The antenna is in wrong
position.
Preset stations
• An incorrect station
cannot be
frequency has been
received
memorized.
• The memorized stations
are cleared.
Poor FM
• No antenna is connected.
reception
• The antenna is not
positioned for the best
reception.
Continuous Weak signals.
hissing noise
during FM
reception,
especially
when a stereo
broadcast is
received.
Continuous or Noise is caused by motors,
intermittent fluorescent lamps, or
hissing noise lightning.
during AM
reception,
especially at
night.
No recording
• Incorrect selection
between the
components.
• Incorrect operation of
each component for
playback and recording.
Remote control
• Batteries are not loaded
unit does not
or are exhausted.
operate.
• The remote sensor is
obstructed.
12

Specifications

Possible Solution
Amplifier
• Connect the cord securely.
• Check the outlet using a lamp or
another appliance.
• Check the speaker connections.
• Adjust the volume.
• Press the MUTE button to cancel
the muting effect.
• Turn on one or both speakers.
• Select the desired input source
correctly.
• Make connections correctly.
FM Tuner Tuning frequency range:
• Connect an antenna.
• Tune in the desired station
frequency.
• Move the antenna and retry
tuning.
• Memorize the correct station
AM Tuner Tuning frequency range:
frequency.
• Memorize the stations again.
• Connect an antenna.
General
• Change the position of the
antenna.
• Change the position of the
antenna.
• Install an outdoor FM antenna.

Legal notices

FCC Part 15
• Keep the receiver away from
noise sources.
• Install an outdoor AM antenna.
• Make connections correctly.
• Operate each component
correctly.
• Replace the batteries.
• Remove the obstacle.
www.insigniaproducts.com
Insignia NS-R2001 AM/FM Stereo Receiver
Notes
• Design and specifications are subject to change
without notice.
• Weight and dimensions shown are
approximate.
• Specifications and external appearance may be
changed for the sake of improvement.
Power output, stereo mode, 8 Ω, THD 1%, 40 Hz~20 kHz:
Total harmonic distortion, 8 Ω, 100 W, 40 Hz~20 kHz:
Intermodulation distortion, 60 Hz:7 kHz= 4:1 SMPTE, 8Ω, 100 W: 0.02 %
Input sensitivity, 47 kΩ, Phono (MM):
Input sensitivity, 47 kΩ, Line (CD, AUX1, AUX2):
Signal to noise ratio, IHF "A" weighted, Phono (MM):
Signal to noise ratio, IHF "A" weighted, Line (CD, AUX1, AUX2): 95 dB
Frequency response Phono (MM), RIAA, 30 Hz~20 kHz:
Frequency response Line (CD, AUX1, AUX2), 20 Hz~100 kHz:
Output level AUX1, AUX2 OUT, 2.2 kΩ:
Bass/Treble control, 100 Hz/10 kHz:
Usable sensitivity, THD 3%, S/N 30 dB:
50 dB quieting sensitivity, mono/stereo:
Signal to noise ratio, 65 dBf, mono/stereo:
Total harmonic distortion, 65 dBf,1 kHz, mono/stereo:
Frequency response, 20 Hz~14 kHz:
Stereo separation, 1 kHz:
Capture ratio:
IF rejection ratio:
Usable sensitivity:
Signal to noise ratio:
Selectivity:
Power supply:
Power consumption:
Dimensions (W×H×D, including protruding parts):
17.32 × 4.87 × 13.12 inches (43.9 × 12.38 × 33.34 cm)
Weight (Net):
This device complies with Part 15 of the FCC Rules. Operation of
this product is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply within the
limits for a class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
2×100 W
0.04%
2.5 mV
200 mV
70 dB
+/- 3 dB
+/- 3 dB
200 mV
±10 dB
87.5~107.9 MHz
15 dBf
25.2 / 45.2 dBf
68/65 dB
0.5 / 0.8%
+/- 3 dB
40 dB
4 dB
80 dB
530~1710 kHz
800 μV/m
40 dB
25 dB
120 V ~ 60 Hz
2.5 A
17.4 lbs (7.9 kg)