Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for boviet SOLAR Vega BVM7612M H-HC-BFDG Series
Summary of Contents for boviet SOLAR Vega BVM7612M H-HC-BFDG Series
-
Page 2: Table Of Contents
MANUAL OVERVIEW 1.1 DISCLAIMER OF LIABILITY 1.2 DECLARATION UNPACKING AND STORAGE INFORMATION SAFETY PRECAUTIONS INFORMATION ENVIRONMENTAL CONDITIONS INFORMATION 4.1 ENVIRONMENTAL CONDITIONS 4.2 INSTALLATION SITE MOUNTING OVERVIEW 5.1 MOUNTING 5.2 MOUNTING WITH BOLTS 5.3 MOUNTING WITH CLAMPS 5.4 GROUNDING ELECTRICAL CONFIGURATION INFORMATION WIRING AND NOTES INFORMATION MAINTENANCE INFORMATION WARNING... -
Page 3: Manual Overview
Boviet Solar assumes no responsibility for any infringement of patents or other rights of the third parties that may result from use of the module. No license is granted by implication or under any patents or patent rights. -
Page 4: Safety Precautions Information
Leave the product in its original packing box until it is ready for installation. If pallets are stored outside temporarily, a protective covering over the pallet should be placed to protect products from direct weathering. Pallets should not be stacked more than one pallet high. At the installation site, keep modules and electrical contacts clean and dry before installation. -
Page 5: Environmental Conditions Information
7. Do not install or handle wet modules. 8. Do not touch the exposed cables or connectors. 9. Do not artificially concentrate sunlight on the solar modules. ENVIRONMENTAL CONDITIONS INFORMATION 4.1. ENVIRONMENTAL CONDITIONS Only Install the PV modules within the following conditions: 1. -
Page 6: Mounting Overview
Panels are not subjected to wind or snow loads exceeding Note: All installation methods herein are only for the maximum permissible loads and are not subject reference. Boviet Solar will not provide related BOS to excessive forces due to the thermal expansion components. The system installer or trained professional of the support structures. - Page 7 Figure 3: PV Module I Mechanical Drawing Table 1: PV Module I Installation Hole Spacing Installation Hole PV Cell PV Module Type PV Module Size Spacing 182-Half-cut BVM7612M-XXX-H-HC-BF-DG (144 cells) A:1300 B:1600 2296*1134*35mm module BVM7612M-XXX-H-HC-BF (144 cells) 166-Half-cut BVM6612M-XXXS-H-HC-BF-DG (144 cells) A:1080 B:1360 2135*1046*35mm module...
-
Page 8: Mounting With Bolts
When the climate of the project site is normal, we recommend using 4-hole mounting (M8 nut). The yellow 4-hole mounting (M8 nut), or blue 4-hole mounting (M8 nut) can be used. When the climate of the project site reaches severe conditions (2400Pa wind load and 5400Pa snow load), the blue or yellow 4-hole mounting (M8 nut) need to be used, in addition to the middle red auxiliary mounting hole (M6 nut). -
Page 9: Mounting With Clamps
5.3 MOUNTING WITH CLAMPS Mounting with clamps at the long side of frames The module frame is not to be modified under any circumstance. When choosing this type of clamp mounting method, please be sure to use at least four (4) clamps on each module, two (2) clamps should be attached on the long sides of the module. - Page 10 Figure 5: PV Module I J and K represent the range of the fixture, A and B represent the module size. Figure 6: PV Module I PV module installed at long side with clamp fitting method...
- Page 11 Figure 7: PV Module I Short Side Mounting Figure 8: PV Module I PV module installed at short side with clamp fitting method...
-
Page 12: Grounding
7. Boviet Solar recommends the method below: 1. A grounding kit with M4 size SS cap bolt, M4 size SS flat washer, M4 size SS cup washer, and M4 size SS nut (with teeth) is to be attach a copper grounding wire to a grounding hole pre-drilled on the frame. -
Page 13: Electrical Configuration Information
Similarly, the inverter automatically turns ON as soon as there is sufficient solar energy from the array to efficiently convert it into grid quality AC Power. Boviet Solar produces following models, XXX presents the power range. Table 4: PV Module Model... -
Page 14: Wiring And Notes Information
Table 5: Electrical Data Technical Highlight Information System voltage (V) DC1000V/1500V Power Tolerance 0~+5W 15/20 Insurance Current (A) ≥ 40MΩ, M Insulation resistance ≥ 40MΩ Application Class Class A Standard Test Conditions (STC) : AM=1.5, E=1000W/m , T=25°C The electrical characteristics are within ±10 percent of the indicated values of Isc, Voc and Pmax under Standard Test Conditions (STC) (irradiance of 100mW/cm², AM 1.5 spectrum, and a cell temperature of 25°... - Page 15 5. The maximum voltage of the system should be less than the maximum certified voltage and less than the maximum input voltage of the inverter and of the other electrical devices installed in the system. To ensure this, the open circuit voltage of the array needs to be calculated at the lowest ambient temperature for the location.
- Page 16 Table 7: PV Module I Connector Images Connector Model Connector Picture Website PV-JM608 jmthy.com PV-JM601 jmthy.com PV-JM601A jmthy.com PV-KSTA/611 -UR (Male) staubli.com/en/ PV-KBTA/611-UR (Female) connectors/ PV-KSTA-EV02/611-UR (Made) staubli.com/en/ PV-KBT4-EV02/611-UR (Female) connectors/ http://www.renhesolar. 05-6-2q com/cn/index.php...
-
Page 17: Maintenance Information
Contact your installer immediately if you suspect your system is not working properly. For any warranty related concerns contact our Boviet Solar after sales service team at service@boviet.com or your sales contact. WARNING: The PV system must be shut down first if it needs any electrical maintenance. Improper maintenance may cause burns and/or electrical shock, which can both be lethal.