Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ALDI LIGHTWAY 872-B-S
Summary of Contents for ALDI LIGHTWAY 872-B-S
- Page 1 User Manual ® BATTERY-POWERED ® SPOTLIGHT ® ®...
-
Page 3: Table Of Contents
Contents Scope of delivery ............4 General information ............8 Reading and storing the user manual ......8 Proper use ................8 Explanation of symbols ............ 9 Safety ................10 Explanation of notes ............10 General safety notes ............11 First use ................16 Checking the product and scope of delivery .... -
Page 4: Scope Of Delivery
Scope of delivery Scope of delivery... - Page 5 Scope of delivery...
- Page 6 Scope of delivery 90° 60° 90° 12 m 2 - 3 m...
- Page 7 Scope of delivery Components Sensor housing LUX controller Motion sensor SENS controller Spotlight head, 2× TIME controller Wall bracket Battery compartment Power switch cover Fixing screw Fastening screw Spotlight Battery compartment Rear panel Batteries, 6× Connecting elements supplied Wall plug, 4× Screw, 4×...
-
Page 8: General Information
General information General information Reading and storing the user manual This user manual accompanies this battery- powered spotlight (referred to below only as the ‘product’). It contains important information on start-up and handling. Before using the product, read the user manual carefully. This particularly applies to the safety instructions. -
Page 9: Explanation Of Symbols
General information Explanation of symbols The following symbols are used in this user manual, on the product or on the packaging. This symbol provides you with useful additional information about start-up or operation. Declaration of conformity (see chapter “Declaration of conformity”): Products marked with this symbol meet all applicable Community regulations for the European Economic Area. -
Page 10: Safety
Safety Safety Explanation of notes The following symbols and signal words are used in this user manual. WARNING! This signal symbol/word designates a hazard with moderate degree of risk which may lead to death or severe injury if not avoided. CAUTION! This signal symbol/word designates a hazard with low risk that, if not avoided, may result in minor or moderate injury. -
Page 11: General Safety Notes
Safety General safety notes WARNING! Risk of explosion and fire! Improper handling of the product can cause an explosion or a fire. − Keep children away from the product. − Keep the product away from water, other liquids, open flames and hot surfaces. - Page 12 Safety sinks or other objects filled with water. − Never use non-rechargeable batteries with this product. − Protect the batteries against mechanical damage. − Do not throw batteries into fire. They could explode or release toxic vapours. − Do not expose batteries to unrestricted sunshine or heat.
- Page 13 Safety WARNING! Risk of chemical burns! Fluid leaked from the batteries could cause chemical burns if it comes into contact with skin or other body parts. Batteries that are swallowed may result in severe internal injuries or even death. − If battery acid leaks out, avoid contact with skin, eyes and mucous membranes.
- Page 14 Safety − If you suspect that a battery has been swallowed or has otherwise entered the body, promptly consult a physician. CAUTION! Risk of injury! The light emitted by the LEDs is very bright and can damage the eyes if looked at directly.
- Page 15 Safety − This product may be used by persons with impaired physical, sensory or mental capacities or those lacking experience and knowledge if they are supervised or have been instructed in how to safely use the product and have understood the risks associated with operating it.
-
Page 16: First Use
First use − The LEDs are permanently installed and cannot be replaced. Once the light source has reached the end of its service life, the entire product has to be replaced. − Stop using the product if any plastic parts of the product show cracks or deformation. - Page 17 First use 1. Take the product out of the packaging. Before start-up, remove all protective films. 2. Check whether the delivery is complete (see Fig. A and B). 3. Check whether the product or the individual parts are damaged. If this is the case, do not use the product. Contact the manufacturer at the service address specified on the warranty card.
-
Page 18: Choosing An Installation Location
First use Choosing an installation location Motion sensors are electronic sensors that recognise movement in their environment and work as electrical switches, responding to this movement. Heat sources are sensed using the lens. If a heat source in the product’s range changes or moves, the spotlight will switch on for the preconfigured time. -
Page 19: Assembly
Assembly Assembly WARNING! Risk of electric shock! Improper installation may result in an electric shock. − Ensure that there are no cables or other electrical lines behind the location where the spotlight is attached. To avoid triggering the product unintentionally, the spotlight must be fitted firmly. -
Page 20: Operation
Operation 5. Screw the rear wall or the wall bracket to the fastening points with screws as based on the properties of the installation surface (see Fig. C). Use a cross-head screwdriver for this purpose. Do not apply excessive force in the process. 6. -
Page 21: Setting The Lighting Time
Operation Setting the lighting time 1. If necessary, turn motion sensor housing to reach the TIME controller 2. Select the desired lighting duration between approx. 10 and 60 seconds by turning the controller in the corresponding direction: − Turning the TIME controller clockwise increases the lighting duration. -
Page 22: Adjusting The Spotlight Heads
Switching the product on and off • Whether the motion sensor reacts depends on the speed at which the object is moving. The sensor will not react to movements that are too fast or too slow. • Electrical sensors are more sensitive in cold, dry weather conditions than in warm, humid climates. -
Page 23: Troubleshooting
Troubleshooting Troubleshooting Fault Possible cause Solution The product The batteries are Insert new batteries. does not empty. switch on The lighting in the Re-configure the despite immediate vicinity LUX controller movement is too bright. find a more suitable in the sensor installation location. - Page 24 Troubleshooting Fault Possible cause Solution The product The following Find a more suitable turns off for movements or location for mounting no obvious heat sources can the spotlight or change reason. activate the sensor: the sensor area by Air conditioning turning the motion units, chimneys, sensor housing...
-
Page 25: Cleaning
Cleaning Cleaning NOTICE! Risk of damage! Improper handling of the product can damage the product. − Remove the batteries before cleaning. − Do not clean the product and accessories under running water, and do not spray the product with the garden hose or a high-pressure cleaner. -
Page 26: Storage
Storage 1. Remove dust and dirt from the spotlight with a soft, slightly moist cloth. For more stubborn dirt, use a mild rinsing agent as required. 2. Let all parts dry completely afterwards. Storage All parts must be completely dry before being stored. −... - Page 27 Technical data Minimum distance to illuminated objects: 1 m Type of protection: IP44 Motion sensor Sensor angle: Approx. 110° (+/- 10°) Rotation: 90° Sensor range: Max. 12 m Sensitivity: 15 to 1,000 lux (adjustable) Lighting duration: Approx. 10 to 60 seconds (adjustable)
-
Page 28: Declaration Of Conformity
Declaration of conformity Declaration of conformity The EU declaration of conformity can be requested from the address specified on the enclosed warranty card. We, AHG Wachsmuth & Krogmann mbH, Lange Mühren 1, 20095 Hamburg, Germany declare in sole responsibility that the product mentioned above meet all applicable regulations and requirements in the economic area of Great Britain. -
Page 29: Disposing Of The Product
Disposal Disposing of the product (Applicable in the European Union and other European states with systems for the separate collection of reusable waste materials) Old devices must not be disposed of with household waste! If the product can no longer be used, every user is required by law to dispose of the device separately from household waste, e.g. - Page 32 PRODUCED IN CHINA FOR: ALDI STORES LTD. PO BOX 26, ATHERSTONE WARWICKSHIRE, CV9 2SH ALDI STORES (IRELAND) LTD. PO BOX 726, NAAS, CO. KILDARE.