Table of Contents Page Description Page Number Safety Precautions Product Overview Description of parts Operation Installation Guide Maintenance Trouble Shooting Technical Specifications Warranty User Information...
May result in death or injury ‘Do Not’ fully submerge the ‘Do Not’ Disassemble, attempt Washloo into water. to repair or alter the Washloo. ‘Do not’ use the product in locations Any alterations should be carried out exposed to excessive moisture and...
Page 5
‘Do Not’ dispose of any burning materials on top of the Washloo. If materials such as cigarettes in the foreign objects enter the product, toilet. This may result in fire or product this may result in electric shock or deformation.
Product Overview Cushion Damper Toilet Lid 3 Pin Plug and RCD Damper/Seat Mechanism Dryer Outlet Side Control Heated Seat Toilet Bowl Nozzle Remote Control Side Control Note : The above illustration is an example only, your version may vary...
Description of Parts Remote Control Remote Control Holder Batteries Remote Control Holder to Wall Installation • Clean Area prior to installation of Remote Control Holder. • Press the tape down firmly and evenly and place on wall. Leave for 15 minutes prior to inserting the remote control Remote Control Holder Double Sided Tape...
The indicator light panel on the remote control displays the position and pressure levels selected by the user The Washloo Prestige is designed to be controlled through the use of the Side Knob and the displayed Remote Control. Note- Indicator panel and LED display may differ depending on specific model configuration.
Page 9
Operation Rear Wash / Oscillating Water Pressure When you are seated and press While cleansing function is operating, press the this button, this activates the `Strong/Lady Care‘ to increase pressure and posterior wash. The nozzle ‘Weak/Child Wash’ to decrease pressure. There are comes out and sprays water on 4 pressure levels from ‘LOW’...
Page 10
3 seconds will turn the function off. Nozzle Clean By pressing the ‘Nozzle Clean’ button, the Washloo will automatically begin Child Wash the Nozzle Cleaning process. Water will This function is designed for children. flow out of the nozzle and clean the Pressing this button activates the peripheral areas around it.
Page 11
Operation Strong Wash When you are seated and press this button it Lady Care activates the ‘Strong Wash’ function, which uses an Front wash will automatically be intensive water pulsation to help remove selected. Water temp will be set to defecation.
Page 12
‘Power Save’ Light on the remote control will flash in order to notify the user of the ‘Power Saving’ setting selected. The seat temperature will be maintained at 25°C and when the user selects the lid to ‘Open’ then the Washloo will automatically turn on. Flush/Auto Flush By pressing this button, the Washloo will ‘Flush.’...
Page 13
Single buzz - When the user sits down and the sensor is activated, the buzzer will sound once. Buzz twice – when operation is attempted when the user is not seated. Buzz three times – The Washloo has detected a fault – please refer to troubleshooting manual.
Page 14
Press the ‘Weak’ and ‘Rear Wash’ button at the same time and hold until the remote control indicator light flashes. Turn the power on to the Washloo using the side control within 5 seconds of the previous step. This will match the code between the remote control and the Washloo Unit (indicator light will stop flashing on the remote).
4. Use the supplied T-Valve/Filter to ensure the Washloo is correctly protected against contaminated/hard water. In hard water areas it is advisable to use an inline water softener. 5. ‘Do Not’ connect the Washloo to the power supply before the installation is complete. Installation Conditions 1.
Page 16
Installation Guide Install Washloo ‘Seal Ring’ 1. Attach the ‘Seal Ring’ to the Drain Outlet of the Washloo (remove cover from the seal ring prior to installation). 2. Position the Washloo onto the ‘Drain Outlet’ ensuring it is correctly lined up and no misalignment (will cause flushing issues if not correctly fitted).
Page 17
2. Insert the electric plug into the designated socket/fused spur as recommended by a qualified electrician. 3. When switched on – all lights on the unit will be illuminated. The Washloo will now prime the water system for around 10 seconds and finally the nozzle will extend out whilst performing a cleaning/first use test function.
NOTE – If the water pressure reduces please remove and clean the filter as shown above. Not using the Washloo for a long period Turn off valve/T- Piece and power supply. Replacement Back-up Battery 1. Turn off power supply.
Trouble Shooting Problem Problem Causes Problem Solutions 1. Make sure the Washloo is plugged 1. Washloo not plugged in. 2. Check the power button on the 2. No power to Washloo. control panel to see if it is turned The Washloo is not 3.
Technical Specifications Product Specification Voltage AC220-240V 50HZ Water Supply Direct connection to water pipe Equivalent to 2 BAR Static Minimum pressure Water Pressure (17L/Min Flow) Water Pressure Adjustable in 4 levels Temperature control (4 Levels, room temperature/33°C/36°C/39°C Adjustable) Inlet water temp to be minimum 15°C ±...
Warranty This electronic bidet has been designed and manufactured with great care and attention to detail. We offer a 24 month warranty. In the following cases the warranty does not apply; 1. Damage or loss sustained in fire, earth quake, flood, thunder or other acts of providence, pollution, gas damage, salt damage and abnormal voltage.
Important User Manual Information If you want to dispose of this product, do not mix with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling. Only discard discharged batteries.
Need help?
Do you have a question about the Prestige and is the answer not in the manual?
Questions and answers