Clam Corp Fish Trap Voyager 8245 Instruction Manual

Clam Corp Fish Trap Voyager 8245 Instruction Manual

Clam corporation fish trap voyager instruction manual

Advertisement

Quick Links

Model No.
- 8245 -
p/n 108304

Specifications

Height:
72" (23" packed)
W idth:
72"
Depth:
93" (37" packed)
W eight: 135 lbs.
- C l a m C u s t o m e r S e r v i c e I n f o r m a t i o n -
NOTICE!! Once used, this shelter cannot be returned to the store. If you have a
Warranty Claim, please contact Clam Corporation Customer Service by email
inquir y or direct by calling:
Customer Service Hrs: - 8am to 4pm, Mon. - Fri. Central Standard Time
Clam Corporation, Inc.
600 Clydesdale Trail
Medina, MN 55340
Phone - 763-231-4120
Fax - 763-231-4121
W ebsite – www.clamcorp.com
Email – www.customerservice@clamcorp.com
C l a m C o r p o r a t i o n , I n c . M a n u a l – 1 0 2 1 7 7

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Fish Trap Voyager 8245 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Clam Corp Fish Trap Voyager 8245

  • Page 1 Model No. - 8245 - p/n 108304 Specifications Height: 72” (23” packed) W idth: 72” Depth: 93” (37” packed) W eight: 135 lbs. - C l a m C u s t o m e r S e r v i c e I n f o r m a t i o n - NOTICE!! Once used, this shelter cannot be returned to the store.
  • Page 2 - P a r t s L i s t - Item 101048 Slide Block 101069 Canopy Pole 101080 1/4" Dia. X 1-1/4" Long Phillips Screw 101081 1/4" Flat Washer 101082 1/4" Thin Locknut 101083 Tube Cap Spacer 101088 1/4" Dia. X 3/4" Long Phillips Screw 101095 Tow Rope 101116...
  • Page 3 - A s s e m b l y D i a g r a m -...
  • Page 4 - S t e p O n e -...
  • Page 5 - S t e p T w o -...
  • Page 6 - S t e p T h r e e -...
  • Page 7 - S t e p F o u r -...
  • Page 8 - S t e p F i v e -...
  • Page 9 - S t e p S i x -...
  • Page 10 - S t e p S e v e n - Slide the Canopy Hoop Poles onto the Canopy Poles until the spring buttons engage the holes near the ends of each Canopy Hoop Pole. Support the first Canopy Hoop Pole as pictured with the Rear Adjustable Spreader Poles (the shorter of the two provided lengths).
  • Page 11 - S t e p E i g h t - Drape the Tent over the supported hoops then go inside and spread out the Canopy Hoop Poles, attaching the Roof Velcro as you go. Orient the Porch Hoop Pole so that the holes face upward and then feed the length of the pole through the three Porch Hoop Sleeves sewn on the Tent.
  • Page 12 - S t e p N i n e - To “set” the Tent, grasp the Tent Material at the rear of the shelter and pull it downward. Observe the porch area of the tent lifting accordingly as you pull. When the U-Channel Molding is correctly installed, the Porch Hoop Pole will lightly touch the floor.
  • Page 13 - S t e p T e n - Angle the Seat Assembly slightly while placing the bottom lip of the Front Seat Bracket under the outside edge of the Base lip. Tilt the complete assembly downward so that the Rear Seat Bracket lands upon the Support Tube. Reach under the Rear Seat Bracket and slide the Latch Clip outwards and then up against the underside of the Support Tube.
  • Page 14 Folding and transporting your Fish Trap is easy: Unsnap the Roof Spreader Poles, Rear Spreader Poles, and Front Spreader Poles. Lay them in the bottom of the base. Push the spring buttons and retract each hoop, starting with the rear hoop and working towards the front.

Table of Contents

Save PDF