Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Techroutes TSR 2800-30
Summary of Contents for Techroutes TSR 2800-30
- Page 1 TSR 2800-30 Hardware Installation Manual...
-
Page 2: Table Of Contents
2.3.3 Cabinet Configuration........................7 2.4 Installation Tools and Device.......................... 7 Chapter 3 Router Installation ............................9 3.1 Installation Procedure of TSR 2800-30 Router....................9 3.2 Installing Router’s Hull........................... 9 3.2.1 Installing the Machine Box on the Desk....................9 3.2.2 Installing the Chassis on the Cabinet....................10 3.3 Connecting the Port ............................. -
Page 3: Chapter 1 Tsr 2800-30 Modularized Router
There are also three interface card slots, one power socket, one power on-off, one grounding column, one ventilation vent and one long-shape ventilation vent. The front template of the TSR 2800-30 modularized router is shown the following figure: Table 1-2 Parts at the front template of TSR 2800-30 Abbrev. -
Page 4: Characteristic Parameters Of The Router
Slot 3 for HIC card supporting the audio card and the 8-asynchronous card) ANT2 Antenna port 2 The back template of TSR 2800-30 router is shown in the following figure: Table 1-3 Parts at the back template of TSR 2800-30 Abbrev. Name Remarks... -
Page 5: Rohs Description
TSR 2800-30 Hardware Installation Manual Power Source’s AC power Characteristics Input voltage: 100-240V Power Input frequency: 50-60Hz consumptio Up to 40W Input current: 1.5A 1.3 ROHS Description... -
Page 6: Chapter 2 Installation Preparation
Avoid severe collision or falling down from the height to protect the parts in the router. Use correct outside ports to connect the router of TSR 2800-30. Do not insert the telephone plug (4-line RJ11 plug) into the Ethernet twisted-pair port or the console port (RJ45 8-line socket);... -
Page 7: Requirements For Common Locations
TSR 2800-30 Hardware Installation Manual Safety Principles for Live Working Put off ornaments, such as ring, necklace, watch and bracelet, before you operate under live working. When metal articles connect the power to the ground, short circuit happens and components may be damaged. -
Page 8: Location Configuration Prevention
TSR 2800-30 Hardware Installation Manual For location planning and device locating, refer to section 2.3.2 “Location Configuration Prevention”. 2.3.2 Location Configuration Prevention The following preventive measures assist you to design the proper environment for the router. Make sure that the workshop is well-ventilated, the heat of electrical devices is well-discharged and sufficient air circulation is provided for device cooling. - Page 9 TSR 2800-30 Hardware Installation Manual MODEM...
-
Page 10: Chapter 3 Router Installation
Installing the Chassis on the Cabinet 3.2.1 Installing the Machine Box on the Desk TSR 2800-30 router can be directly put on the smooth and safe desk. Note: Do not put things weighing 4.5 kg or over 4.5 kg on the top of the router. -
Page 11: Installing The Chassis On The Cabinet
3.3 Connecting the Port 3.3.1 Connecting the Console Port TSR 2800-30 modularized router has one console port and one remote assistant console port. Its attributes and usage method are described in this section. 1. Console port The console port has a rate of 1200bps to 115200bps and a standard RJ45 plug, the parity check is an option for the console port and the flow on the console port can be controlled. - Page 12 It is used to connect the Modem. Signal ground The cable is used to connect the console port of the TSR 2800-30 modularized router and the outside console terminal device. One end of the cable is a 8-pin RJ45 plug and the other end is a 9-hole plug (DB9). The RJ45 plug is put into the socket of the console port on the TSR 2800-30 modularized router.
-
Page 13: Connecting1000M-Ethernet Electric Port
TSR 2800-30 Hardware Installation Manual Figure 3-1 RLC0301 inner line connection 3.3.2 Connecting1000M-Ethernet Electric Port The 10/100/1000M auto-adaptation Ethernet port provides the UTP (RJ45) interface and has the link/ACT indicators. The 10/100M auto-adaptation Ethernet port can be connected to the UTP port of the router and then to HUB through the twisted pair. - Page 14 TSR 2800-30 Hardware Installation Manual 1. Connecting the 10/100/1000Mbps auto-adaptation Ethernet port and HUB 2. Pins of the UTP port Pin Name Symbol Sending and receiving TP0+ the normal phase of data 0 Sending and receiving TP0- the paraphase of data 0...
-
Page 15: Connecting The Usb Port
TSR 2800-30 Hardware Installation Manual data 3 Sending and receiving TP3- the paraphase of data 3 3.3.3 Connecting the USB Port The USB interface supports the physical-layer protocol of USB2.0. The USB port works in main mode, which can be plugged into the sub-device. - Page 16 TSR 2800-30 Hardware Installation Manual The following table lists slot-supported NICs: Slot1 and slot2 support all kinds of cards, while slot3 only supports HIC-8ASY cards, HIC-2FXO cards and HIC-2FXS cards. Note: Do configuration according to the following table and do not incorrectly insert NIC into a slot.
-
Page 17: Chapter 4 Router Maintenance
TSR 2800-30 Hardware Installation Manual Chapter 4 Router Maintenance Caution: Before opening the machine box, make sure that you have released the static you carried and then turn off the power on-off of the router. Before operating any step in Appendix B, read the section “Safety Advice”. - Page 18 TSR 2800-30 Hardware Installation Manual See the following figure. When the cover and the bottom are closely tied, let the cover slide the slot of the front template at the bottom. Nail the bolt and screw it tightly with the screwdriver.
-
Page 19: Chapter 5 Hardware Fault Analysis
When the system runs abnormally, it is ALARM Power LED System indicator When the system is started, it flickers. Each TSR 2800-30 router has its own indicators, names and description of which can be seen in Interface Card Installation Manual. -18-... - Page 20 TSR 2800-30 Hardware Installation Manual Copyright Claims Without the written approval of the company , any person or group cannot transcribe, copy or change partial or all contents of this manual, and must not broadcast it in any manner. Trademark claims...
Need help?
Do you have a question about the TSR 2800-30 and is the answer not in the manual?
Questions and answers