Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SAMWAY P20D
Summary of Contents for SAMWAY P20D
- Page 1 Operation Book Read Before Opeartion P20D USER MANUAL SAMWAY www.samway.com...
-
Page 2: Table Of Contents
4. START - UP ..................6 - 9 4.1 MACHINE PLACEMENT ................. 6 4.2 SELECTING DIES .................. 6 4.3 P20D CONTROL PANEL lLLUSTRATION ..........7 4.4 CHANGE OF A SINGLE DIE ..............8 4.5 CRIMPING ....................8 5. SELECTING THE DIE SET, 20 MODEL ..........9 6. -
Page 3: Introduction
SAMWAY is not liable for injury/damage to persons/machine or property as a result of improper use, having made prohibited modifications to the machine or misinterpreting this manual’s safety instructions. -
Page 4: Equipwent
The warranty dose not cover improper use or normal wear. Travel costs, time for repair and shipping costs are not covered by the warranty. Repairs under the warranty are to be made only by SAMWAY or an authorized service technician approved by SAMWAY. Lost income or extra costs that may arise for any reason are not covered by the warranty. -
Page 5: Important
P20 is designed manufactured and made safe for crimping hydraulic hose in dimensions 3/16”-1”.Any other use of this machine is considered improper and SAMWAY is not liable for injury or damage to persons, property or the machine. The machine shall only be used for crimping hydraulic hose according to specification. -
Page 6: Start-Up
P20D USER MANUAL EDITION 2019 www.samway.com P20D 4. START-UP 4.1 Machine placement Place the machine on a stable and flat surface. 4.2 Selecting dies Determine the crimping dimensions for the current operation and select the die set with the correct interval that corresponds to the crimping measurement. -
Page 7: P20D Control Panel Lllustration
P20D USER MANUAL EDITION 2019 www.samway.com 4.3 P20D control panel illustration Motor Stop Motor Start Semi-Automatic Control Semi-Automatic Control Symbol Manual Opening Button Crimping data adjustment Foot Pedal Control Mode Back Stop Control Mode Mode Selection Semi-Automatic Mode L. S... -
Page 8: Change Of A Single Die
P20D USER MANUAL EDITION 2019 www.samway.com 4.4 Change of a single die Open the dies to the maximum retraction. Open the supply disconnecting device. CAUTION! SUPPLY DISCONNECTING DEVICE SHALL ALWAYS OPENED DURING INSTALLATION OF THE DIES. Prior to installing the dies, clean the contact surface of... -
Page 9: Selecting The Die Set, 20 Model
P20D USER MANUAL EDITION 2019 www.samway.com 5. SELECTING THE DIE SET, 20 MODEL From crimping diameter chart, delivered together with the machine, you can see the die numbers corresponding crimping ranges. The upper section of the chart shows the corresponding dial... -
Page 10: If The Machine Does Not Work
P20D USER MANUAL EDITION 2019 www.samway.com 6. IF THE MACHINE DOES NOT WORK… If the motor doesn’t start up 1. To start up the machine, turn the switch completely to the left (0) and then to the upright position (I). -
Page 11: Re-Calibration Of Crimping Diameter Dial
P20D USER MANUAL EDITION 2019 www.samway.com 7. RE-CALIBRATION OF CRIMPING DIAMETER DIAL NOTE: The crimping diameter dial has been calibrate d at the factory during test run. Re-calibrate the crimping diameter with ferrule (seamless steel tube), Ø 25 mm; wall 2 mm, by using the die set No 20-19 (20 model) or the die set 32-19 (32 model). -
Page 12: Samway P20D
* Special Die sets or dedicated die sets for RYCO PARKER Manuli Eaton hose available upon request WUXI SAMWAY CO.LTD SAMWAY whatsapp +86 138 120 22928 ; SKYPE : samway.company Tel: 0086-510 8378 8458 ; Mobile: 0086 13812022928 samwaysales@gmail.com ; www.samway.com samwaysales@gmail.com...