Advertisement
Quick Links
Technical Data
Setting up: Benchmodel or Standmodel
Speed Regulation with Potentiometer
Changing the spindle direction
Mainswitch, ASS-Safety System at Spindle
Magnet Box with buttons and switches
"0" Point adjustment for Tip-to-Tip alignment
Safety instructions, clamping of workpieces
Tool Rest Base/Support and upper part
Outrigger and Bed Extension (options)
Declaration of conformity
OPERATING INSTRUCTION KM 1450
03-2020
2
3
4
5
6
7
8-9
10
10
11
Advertisement
Related Manuals for steinert KM 1450
Summary of Contents for steinert KM 1450
-
Page 1: Table Of Contents
OPERATING INSTRUCTION KM 1450 03-2020 Standard Accessories Technical Data Liability Setting up: Benchmodel or Standmodel Electric Connection Operating the Lathe Speed Regulation with Potentiometer Changing the spindle direction Mainswitch, ASS-Safety System at Spindle Magnet Box with buttons and switches “0” Point adjustment for Tip-to-Tip alignment... - Page 2 Headstock Hinge for Vee-belt-cover Lock pin for 36-indexing system Digital Display for read out The adjusted spindle speed RED main Button “on/off” If button is pushed: Lathe is disconnected from electric mains all buttons of Mobile Box without function Black Lock Pin for Headstock swivelling Vee-Belt-POulley with integrated indexing system Handle to lift motor for changing...
-
Page 3: Standard Accessories
STANDARD ACCESSORIES 4-prong mandrel MT2 D=25 mm for spindle inner cone Pictures shows also the ASS-safety-ringnut at the spindle and scale of indexing system Live centre with ball-bearing MT2/60° for cone of tailstock quill quill with engraved scale 1 Tool Rest support 1 Tool Rest 350 mm, stem D=30 mm 1 Double cone MT2/MT2 for re-adjusting “0”... - Page 4 Pin to lock spindle to loose the chucks from spindle thread 1 long bar D=8 mm to push out the prong mandrel from spindle cone 1 Pin D=8 mm for chucks with a Bo=8,1 mm to loose the chuck from spindle thread never insert the pin into the boring of the handwheel sleeve !!
- Page 5 TECHNICAL SPECIFICATIONS 200 mm Centre height 710 mm Centre Distance 400 mm Swing over bed 660 mm max. Turning Diameter with outrigger Hollow Spindle D=10 mm with inner cone MT2 Spindle thread outside M33x3,5 with centering collar and ASS safety-ring-nut Spindle speed 3 step pulley: 40-850...
-
Page 6: Liability
LIABILITY It is not permitted to make alterations or additions to the construction of the machinery supplied, to parts of the machinery supplied or to accessories. Any warranty and liability claims become void in such case. SETTING UP THE MACHINE The anti-rust protection must be removed from the bright machine parts before first use. -
Page 7: Operating The Lathe
OPERATING THE LATHE SPEED REGULATION the spindle speed is automatically stopped if the vee-belt cover is opened! Push red main Button “OFF” before you open the vee-belt cover! Infinitely speed regulation is performed by the 3 step pulleys: Changing vee-belt to requested pulley: ... - Page 8 MAINSWITCH and EMERGENCY-OFF-BUTTON The lathe is switched on by the RED Main Button at the headstock: release button Not until then are all switches/buttons at the Mobile box activated. During working with the lathe use only the buttons and functions at Mobile Box After working time: push in the red main switch button at headstock to disconnect the lathe from electric mains.
-
Page 9: Swivelling Of Headstock
SWIVELLING OF HEADSTOCK the headstock can be swivelled in 6 different positions: 0/60/90/120/180/270° Do not swivel the headstock during turning reps. If the spindle motor is running switch off the motor/spindle loosen the headstock fixing lever on lefthand side of headstock ... - Page 10 SAFETY INSTRUCTIONS additional safety instruction see EG-conformity declaration The vee-belt cover must be closed after each change of V-belt position by the hinge otherwise motor does not run on: turn potentiometer down to “0” Before the machine is switched ...
-
Page 11: Maintenance
BED EXTENSION (Option) Screw the extension first just hand-tight with both lower screws at the face of lathe bed Align the bed extension to the top and side of standard lathe bed (use only rubber hammer) Check if there is no step, if the tailstock runs smooth over the both bed parts Finally set in the upper screws and tighten all 4 screws MAINTENANCE The machine requires no maintenance. - Page 12 RE-ADJUSTMENT OF “0-Point-Locking” Level the lathe with a spirit level (righthandside and lefthandside cross to lathe bed) + use the supplied adjusting screws + metal and rubber plates Double cone MT2/MT2 Insert Double cone into tailstock quill Loosen tailstock clamping Move tailstock close to the headstock until the cone is inserted into the spindle cone Clamp tailstock...
- Page 13 Loosen clamping lever of headstock move out the quilll of tailstock in direction to the headstock by turning the handwheel headstock moves lightly to the lefthandside: clamp now the lever of headstock headstock and tailstock stands to each other Loosen tailstock clamping insert the long bar from lefthandside through the handwheel into the hollow spindle and push out the double cone with tailstock to the righthand...
- Page 14 Headstock Clamping must be fixed loosen the 2 x black hexagon socket screws SW5 (left and right) from the 0-point-locking use any pocket lamp to help adjusting the 0-point-locking by a “light-gap-method” push down the yellow bolt/slide it must touch now parallel the inner front of lathe cheek without any light-gap-sight press on the bolt and fasten evenly the both black screws again...
- Page 15 EN 13849-1 EN 60 204 T 1 EN 1088 Diese Erklärung wird verantwortlich für DRECHSELZENTRUM ERZGEBIRGE - steinert® abgegeben durch: This declaration is made for and on behalf of DRECHSELZENTRUM ERZGEBIRGE - steinert® by: Roland Steinert (Inhaber / Owner) Unterschrift:_______________________________________...