Related Manuals for Nexar HaloCam
Summary of Contents for Nexar HaloCam
- Page 1 WELCOME TO The Complete Package for Safety & Video Evidence DashCam START HERE!
- Page 2 In this manual, we’ll show you how to install the HaloCam in your vehicle and connect it to the Nexar app for the safest driving experience possible. Let’s go! support@getnexar.com...
- Page 3 DOWNLOADING THE NEXAR APP If you haven’t yet downloaded the Nexar app, do so first:* Download the app by searching for ‘Nexar’ in the App Store (iPhone) or Google Play (Android) Open the app, register, and enable all necessary settings when prompted...
-
Page 4: Package Contains
PACKAGE CONTAINS HaloCam Holder USB charger USB power cable Installation tool Micro SD card Cable clips support@getnexar.com... -
Page 5: Assembling The Camera
ASSEMBLING THE CAMERA Insert micro SD card into the micro SD slot on the camera until you hear a click Insert the holder into the holder slot on the camera and slide to lock in place (The SD card may be pre-slotted for you) Remove sticker from camera lens To turn camera on and off, single tap the POWER button. - Page 6 ACTIVATING THE CAMERA IN YOUR VEHICLE Connect the charging cable to the camera’s POWER port support@getnexar.com...
- Page 7 Install the USB charger in your vehicle’s power socket Connect the other end of the charging cable to the USB charger’s 1A socket Start your vehicle...
- Page 8 Open your iPhone’s settings Wi-Fi Tap on WiFi Connect to the WiFi network Nexar (5G) that begins with ‘Nexar (5G)’ Enter password: 12345678 Don't worry, your cellular data is still available Note: Make sure the blue WiFi light is never on.
- Page 9 IN DRIVE Double-press the camera’s power button Auto start rides The camera’s WiFi indicator light will now flash blue Open the Nexar app Go to Settings in the top-right corner DEVICES Tap External camera External camera After a few seconds, the camera and your...
- Page 10 INSTALLING THE CAMERA IN YOUR VEHICLE sticker lens towards the road windshield Open Nexar and tap the camera icon (for Android) or the Drive button (for iPhone) Wait a bit, your camera’s feed will show up in the Nexar app Before sticking your camera to the windshield, make sure it has a clear view of the road.
- Page 11 Location to ‘Always’. Then go to the settings screen inside the app and turn on ‘Auto start drive’. On Android - Go to Nexar’s settings menu in the app, and make sure ‘Auto start rides’ is on. Also, make sure your phone’s GPS is on.
- Page 12 HOW TO HIDE THE CAMERA’S CABLE Watch the video: nxr.cm/hidecables Sit in the passenger seat With one hand, gently pull downthe edge of the fabric at the top of the windshield With your other hand, use two fingers or the installation tool to insert the cable behind the ceiling fabric You can use the cable clips provided if you prefer 12 |...
- Page 13 Open the passenger-side door Insert the cable into the door’s seal from top to bottom Bring the cable behind the glove compartment Insert the remaining cable under the passenger-side floor mat Bring the cable as close to the power socket as possible, and connect the cable to the USB charger | 13...
- Page 14 STRUCTURE & BUTTONS Rear camera port Heat dissipation holes Holder slot Reset button POWER port Camera lens Speaker Power indicator light WiFi indicator light Microphone Power button Micro SD card slot Heat dissipation holes 14 | support@getnexar.com...
- Page 15 Additional Info: Note: The camera will turn on and off automatically when you start and stop your vehicle. Indicator Lights: 1. Green light on: Camera powered on and active. 2. Red light flashing: Firmware upgrading. 3. Blue light flashing: Camera waiting for a WiFi-direct connection (for Android only). 4.
-
Page 16: Drive Safely
When you use our free app and a Nexar-ready dash cam, you join a safe driving network of vehicles. As more drivers in your area join this network, Nexar will start warning you of dangers on the road ahead. -
Page 17: Fcc Warning
FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the HaloCam and is the answer not in the manual?
Questions and answers