Table of Contents
Advertisement
CHARGING
ADHERE STRICTLY TO THESE
WARNING
AND ALL OTHER SAFETY
INSTRUCTIONS AND GUIDELINES
• Ensure a barrel blocking device is fitted to the ANGEL.
• Ensure the hopper is removed from the ANGEL.
• Ensure that there are no paintballs in the ANGEL.
• Ensure the ANGEL is switched off via the isolating switch at the rear of the
marker prior to fitting your first stage regulator.
• Paintball industry standard eye/face/ear and head protection designed
specifically to stop paintballs and meeting ASTM standard F1776 (USA) or CE
standard (Europe) must be worn by user and any person within range.
Before initial use of the ANGEL, it is necessary to give the power pack a full charging
cycle of 4 hours prior to use as this will ensure a long life for the power pack.
Subsequent charges will be in the region of 3 hours for a full charge, the
electronics will control the charging cycle and ensure that your battery is fully
charged.
The ANGEL may be left charging for prolonged periods without damage
occurring to the battery pack.
• A full charge will give sufficient power for approximately 150,000
consecutive shots.
• A 1-hour charge at 12.5V DC will give sufficient power for approximately
40,000 consecutive shots.
The ANGEL will continue to use power whilst it is switched ON.
To save the charge the isolator switch must be switched OFF to isolate the
battery.
We recommend the isolating switch be placed in the OFF position when the
ANGEL is in storage, transit or not in use.
• Insert cigar lighter adaptor into a negative earth socket as found in
most motor vehicles (red light on charger will illuminate to indicate that
power is present).
• Insert remote plug from charger into the socket on the rear of the
ANGEL. The socket is located on the rear of the grip frame under a
rubber protection grommet.
© 2005 WDP LTD.
Charging – Switching On Your ANGEL
• Ensure the isolator switch is in the ON position at the rear panel of the
ANGEL. See SWITCHING ON YOUR ANGEL - right.
• The LCD on the ANGEL display will indicate the status of the charging
cycle, the bar graph segments on the display will cascade to indicate
charge is being taken.
• When a full charge has been taken the bar graph segments will remain
illuminated.
• Removal of the charger before a full charge cycle has been completed
will result in a short charge.
• Unplug the charger from the ANGEL and replace the rubber grommet
cover on the rear of the grip frame to prevent the entry of dirt or debris.
IMPORTANT NOTES: For Battery Charging
• Should the ANGEL be "LIVE" the insertion of the charger will make the
ANGEL "SAFE" and unable to fire and removal of the charger will cause
the marker to remain in this state until the ANGEL is made "LIVE" again by
pressing the red button on the back of the grip frame for 2 seconds.
• Supply voltage must be minimum 12V DC, maximum 24V DC, negative
earth.
• The isolator ON/OFF switch on the back of the ANGEL must be in the ON
position to charge the battery.
• The battery must be plugged into the circuit board.
• Removal of the charger before a full charge cycle has been completed
will result in a short charge. Check your vehicle handbook for voltage and
current capabilities prior to use.
• Use only the charger supplied for charging the ANGEL.
OPERATION
SWITCHING ON YOUR ANGEL
ON
OFF
OFF
ON
ADHERE STRICTLY TO THESE
WARNING
AND ALL OTHER SAFETY
INSTRUCTIONS AND GUIDELINES
• Ensure a barrel blocking device is fitted to the ANGEL.
• Ensure the hopper is removed from the ANGEL.
• Ensure that there are no paintballs in the ANGEL.
• Ensure the ANGEL is switched off via the isolating switch at the rear of the
marker prior to fitting your first stage regulator.
• Paintball industry standard eye/face/ear and head protection designed
specifically to stop paintballs and meeting ASTM standard F1776 (USA) or CE
standard (Europe) must be worn by user and any person within range.
• Ensure the battery is charged.
• Rotate the breech release lever clockwise to gain access to the
ON/OFF switch.
• Switch the isolator switch to the ON position.
• The LED on the rear of the grip frame will be Green.
• The LCD display will show software version and will be "LIVE'.
• To make the Angel enter into "SAFE" either turn the isolator switch OFF
or press and hold the top button for 1.5 seconds the display will now
show "SAFE".
ANGEL G7
3
Advertisement
Table of Contents
