Page 1: Table Of Contents
• En cas de doute, ou s’il vous est impossible de comprendre Terms of Warranty - EEC/R.O.W Exc USA/CAN le contenu du monde d’emploi, demandez conseil à un expert. FIGURES WDP Ltd. Express Warranty USA/CAN Only Updates 1 Basic & Advanced Menus Your Personal Details...
Page 2: Warnings
• Do not ﬁre the ANGEL with the breech open or without the bolt in the breech, EVENT OF RESALE OR NEW OWNERSHIP. as high pressure gas will be emitted. • SHOULD YOU BE UNSURE AT ANY STAGE YOU MUST SEEK EXPERT ADVICE. © 2005 WDP LTD.
Page 3: Charging
(red light on charger will illuminate to indicate that power is present). • Insert remote plug from charger into the socket on the rear of the ANGEL. The socket is located on the rear of the grip frame under a rubber protection grommet. © 2005 WDP LTD.
Page 4: Making The Angel Safe
• GREEN CONSTANTLY ON = SAFE mode. LED INDICATOR STATUS ON THE REAR OF THE FRAME • RED CONSTANTLY ON = LIVE mode, ANGEL EYES OFF. • RED SLOWLY FLASHING = LIVE mode, ANGEL EYES ON. © 2005 WDP LTD.
Page 5: Loaders (Hoppers)
• Do not ﬁre the ANGEL with the BREACH RELEASE LEVER in the unlocked ﬁrst stage regulator removed. Always discharge the marker in a safe direction • To maximise the performance of the ANGEL, WDP recommends only using position. to relieve this residual gas pressure.
Page 6: Velocity Adjustment
• The new input pressure to the ANGEL may be observed from the micro pressure indicator on the ﬂash tank. IMPORTANT NOTE: • When reducing velocity, allow four shots for the complete system to be at the new regulated pressure. © 2005 WDP LTD.
Page 7: Lcd Menus
0.1 to 2.0 seconds. This is the time period that the intellifeed will supply a • When the paintball is detected the display will show ‘PASS’. signal output for the hopper (loader). • Failure to obtain the ‘PASS’ message is an indication that the Angel Eyes need cleaning or servicing. © 2005 WDP LTD.
Page 8: Internal Electronic Menus
• The ANGEL Semi Limited with Angel Eyes works on the following principles: damping. • The Angel Eyes will default to ON whenever the ANGEL is made LIVE via the top button located at the rear of the frame. © 2005 WDP LTD.
Page 9 No External Access - see fig. 2 Drop 1 paintball into breech. Shot Counter ANGEL EYE TEST TRIP CYCLES If detected, ‘PASS’ will be shown. Hold to return to zero Total Shots Non Resetable BASIC TO ADV TO BACKLIGHT MENU © 2005 WDP LTD.
Page 10: Internal Menu
Or press to clear and return Or press to clear and return to Step 4. to Step 4. TEXT SET PIN SET Upon confirmation, Upon confirmation, the LCD will display ‘SET’ the LCD will display ‘SET’ © 2005 WDP LTD.
Page 11 To make the ANGEL Safe, Hold for 2 seconds. CONFIRM PIN Press to confirm PIN. If PIN correct, ANGEL will enter RETURN TO SAFE ‘SAFE’ Unlocked Mode. Or press to clear and return to Step 4. © 2005 WDP LTD.
Page 12: General Care And Cleaning
0.375 inches (10mm) into the bottom of the frame otherwise damage will occur to the electronics. We recommend that you remove the left-hand cheek cover and ensure the screws do not project into the circuit board cavity when ﬁtting. © 2005 WDP LTD.
Page 13 General Assembly: Left Hand View – Sub Assemblies MAINTENANCE ANGEL G7 TWIST LOCK GATED FEED BATTERY ANTI DOUBLE BALL VERNIER WHEELS END PLUG FLASH TANK SOLENOID ASSEMBLY CONTROL BUTTONS GRIP FRAME PCB OPTO BOARD MINI-REGULATOR GRIP CHEEK © 2005 WDP LTD.
Page 15: Mini-Regulator Service
• Ensure that the Angel Eyes are not moved or trapped. • Remove the mini-regulator adjuster screw • Remove the mini regulator locking screw • Remove the mini regulator end cap by inserting a M4 allen key into the macro line ﬁtting and rotating counter clockwise. © 2005 WDP LTD.
Page 16 • Ensure no wires become trapped between the body and grip frame during • Ensure the cover plates are inserted correctly into the ANGEL body re-assembly. • Ensure that the Angel Eyes are not moved or trapped. • Ensure the plugs are located in the correct sockets. © 2005 WDP LTD.
Page 17: Lpr Adjustment
• THE ANGEL IS LIVE AND CAPABLE OF DISCHARGING. • Fire 6 shots with NO paintballs present to stabilize the LPR pressure. Note the pressure reading. Should the reading be too high or low, proceed to the next stage. © 2005 WDP LTD.
Page 18: Lpr Assembly Removal
• Remove the 3 tri-active piston spring stack 7. • Remove the shims 8 - Note: the number of shims may vary from shown diagram. • Using a suitable blunt pick, carefully withdraw the LPR body 9. © 2005 WDP LTD.
Page 19: Exhaust Guide Removal
• When the holes line up insert the lock pin into the hole. • Ensure no wires become trapped between the body and grip frame during re-assembly. • Ensure the plugs are located in the correct sockets. © 2005 WDP LTD.
Page 20: Ram Removal
• Remove the 2 grip frame screws 8 holding the frame to the body using a suitable 3mm A/F Allen key. • Remove the grip frame 9 from the body. • Withdraw the ram lock pin located under the frame. The ram can now be withdrawn as an assembly. © 2005 WDP LTD.
Page 21: Opto Board
• By viewing the ANGEL on the left hand side of the body rotate the thumb wheel furthest from the rear of the ANGEL slowly towards the rear of the ANGEL each click at a time, this will reduces the return stroke, each clickwill be an incremental reduction in the stroke. © 2005 WDP LTD.
Page 22: Vernier Trigger Wheel Removal
3mm A/F Allen key. • Remove the grip frame from the body. • Gently remove the vernier wheels from the body. • Remove the vernier wheel ratchet plates and inspect for damage. © 2005 WDP LTD.
Page 23: Battery Removal
2.0mm A/F metric Allen key. • Do not pull the plugs out from the PCB by the wiring use a suitable tool. • Carefully lift the back plate off . © 2005 WDP LTD.
Page 24: Fault Finding Table
Check solenoid valve. Therefore a paintball @ 3.2grams @ 300Ft/s= 9.9 foot lbs (ftlbs) From the Ram assembly? Check ram body O rings. From the gas joints? Check all ﬁttings. 12-14 From exhaust valve? Exhaust valve stem/guide. © 2005 WDP LTD.
Page 25 TERMS OF WARRANTY - EEC/R.O.W. EXCLUDING USA / CANADA Subject to the conditions set out below WDP Ltd. warrants that the ANGEL Except in respect of death or personal injury caused by the company’s will correspond to its speciﬁcation at the time of delivery and will be free from...
Page 26 Warranty. The replacement or repair third party beneﬁciaries to this Warranty herein. NO WARRANTY IS PROVIDED of a product by WDP Ltd. does not give rise to any new Warranty except the TO DISTRIBUTORS OR DEALERS EXCEPT AS MAY BE EXPRESSLY PROVIDED IN Warranty period provided for herein shall be extended by the length of any A SEPARATE AGREEMENT OF SALE.
Page 27: Your Personal Details
Our products are continuously updated and changes may be made to speciﬁcations, design, or appearance from time to time. For the latest speciﬁcation, virtual products and on line technical support we PURCHASE DETAILS recommend that you visit our website: www.wdp.tv. MODEL/COLOUR BODY/BLOCK SERIAL NO UNIQUE ELECTRONIC ID NO.

WDP ANGEL G7 Operators And Users Manual

Quick Links

Related Manuals for WDP ANGEL G7

Summary of Contents for WDP ANGEL G7

Table of Contents