HD62 User Manual Content CHAPTER 1 NOTES AND SAFETY REQUIREMENTS ------------------------------------ 1 1.1 Cautions and Notes -----------------------------------------------------------------1 CHAPTER 2 PACKING LIST ------------------------------------------------------------ 2 CHAPTER 3 FUNCTION INTRODUCTION OF EACH PART----------------------------- --3 3.1 Name and Function for Each Part of Microscope ----------------------------------- 3 3.2Accessory Introduction ------------------------------------------------------------ - 5...
HD62 User Manual Chapter 1 Notes and Safety Requirements 1.1 Cautions and Notes To avoid danger or damage incurred to the lens, do not touch the lens or sensor directly with your fingers. To avoid failure or electric shock hazard and so on, do not disassemble or modify the internal structure of the device.
HD62 User Manual Chapter 2 Packing List 1. .Imaging part and arm 2. Monitor 3. Base 4. Upright column 5. Hand shank 6. AC/DC adapter 7. HDMI cable 8. USB cable 9. inner hexagon spanner 10. Installation disk Reset pin 11.
HD62 User Manual Chapter 3 Function Introduction of Each Part 3.1 Name and Function for Each Part of Microscope KS064300G4-Ver1.1 - 3 -...
Page 6
HD62 User Manual 1. Monitor 12.5"monitor, For image display and USB power supply interface. Rotate the knob to implement the focus function; Rotate 2. Focus knob clockwise: back focal length decreases and object distance increases; Rotate anticlockwise: back focal length increases and object distance decreases.
Page 7
HD62 User Manual Support rotation and tilt of the monitor. 16. Shaft Power supply to the monitor. 17. Power interface Loosen the knob to adjust the lens position. After 18. PTZ master knob tightening the knob, the lens can be fixed at the current position.
HD62 User Manual 3.2 Accessory Introduction USB cable The digital microscope can be powered by connecting to the adapter. Connecting the digital microscope HDMI cable to and monitor to achieve signal transmission between digital microscope and monitor. Power adapter Connect and supply power to the monitor.
HD62 User Manual Chapter 4 Installation Guide 4.1 Methods of application of electron microscope 1. Assembly: 1) Screw out three screws on the round column with medium hex wrench ,Lock the bottom plate and the round column, shown as image 1 2) Lock the articulating arm on the round column, shown as image 2.
HD62 User Manual Chapter 5 Digital camera Instructions 5.1 Instruction of manual focusing knob on the top of the digital camera 1. Connect the relevant accessories such as digital microscope and monitor, etc. (For detailed operation, please refer to Chapter 4) 2.
HD62 User Manual 2. PTZ chassis locking knob (1)counterclockwise rotation:Loosen the knob to rotate within 180 degrees. (2)clockwise rotation:Lock the current position of the lens. 5.3 Articulating arm adjustment Articulating arm strength adjustment: “+”: When the bracket cannot support the weight of the lens, adjust the hex screw in the "+"...
HD62 User Manual 5.2 Introduction of buttons functions a) 5 buttons are set on the machine body. b) Short press refers to press time 0.2s~1s. Long press refers to press time more than 2s or above. (Without special reference, press below all means short press).
HD62 User Manual 4) Freeze Under photo or recording mode, long press to freeze the picture and press to unfreeze it. When the picture is frozen, press to save the frozen on screen as picture. 5) Menu Setup Pressing to enter the menu bar interface. Through button ”...
HD62 User Manual (2) With the cursor pointed to , through button to process single automatic exposure. Red icon TE stands for ongoing real-time automatic exposure and black TE for none automatic exposure or completed single automatic exposure. (3)With the cursor pointed to...
HD62 User Manual 5.3 Read TF card After connected the digital camera to the USB port of the PC, press to switch the USB mode to TF card mode. Meanwhile a disk icon will be created on the computer and the file in TF card of the digital camera can be read through computer.