Related Manuals for Hussmann RMID
Summary of Contents for Hussmann RMID
- Page 1 RMID Cheese/Deli Island Case RMID/C p/n IGIC-RMID/RMID-HT -0109 INSTALLATION & OPERATION GUIDE...
-
Page 2: Table Of Contents
HUSSMANN CHINO PRODUCT CONTROL The serial number and shipping date of all equipment has been recorded in Hussmann’s files for warranty and re- placement part purposes. All correspondence pertaining to warranty or parts ordering must include the serial num- ber of each piece of equipment involved, in order to pro- vide the customer with the correct parts. -
Page 3: Cut & Plan Views
Rev.0109 Plex Perimiter Lights Lights " 6" 24" 36" RMID-3' with Standard CAD Scale = 1/2" 48" (Various Lengths) MECHANICAL STUB-UP AREA 18” X 18” RMID-4' OCTAGON Scale = 1/2" " Food Lights Warmer " Lights Ref. Display " 48"... -
Page 4: Leveling
Installation LOCATION The refrigerated merchandisers have been designed for use only in air conditioned stores where temperature and humidity are maintained at or below 75°F and 55% rela- tive humidity. DO NOT allow air conditioning, electric fans, open doors or windows (etc.) to create air currents around the merchandiser, as this will impair its correct operation. -
Page 5: Refrigeration
Rev.0109 condensate drains to insure a proper installation: 1. Never use pipe for condensate drains smaller than the nominal diameter of the pipe or P-trap supplied with the case. 2. When connecting condensate drains, the P-trap must be used as part of the condensate drain to prevent air leakage or insect entrance. -
Page 6: T-Stat Location
Hussmann cases were not designed to “heat up” or “cool down” product—but rather to maintain an item’s proper temperature for maximum shelf life. To achieve the pro-... -
Page 7: Case Cleaning
2. Keep the air in and around the case area free of foreign gasses and fumes or food will rapidly dete- riorate. 3. Maintain the display merchandisers temperature controls as outlined in the refrigerator section of this manual. 4. Do not place any product into these refrigerators until all controls have been adjusted and they are operating at the proper temperature. -
Page 8: Maintenance
TOWARD THE MOTOR. COPPER COILS The copper coils used in Hussmann merchandisers may be repaired in the field. Materials are available from local refrigeration wholesalers. Hussmann recommends using #15 Sil-Fos for repairs. - Page 9 Rev.0109 3. Drill out all pop rivets (C). holding upper flare using a 1/8" drill bit. 4. Remove flare taking care not to bend it. The ends of the flare are double taped together separate without creasing. 5. Unscrew plex from case (D). 6.
- Page 10 INSTALLING SPLASHGUARD After merchandisers have been leveled and joined, and all drip piping, ELECTRICAL and refrigeration work has been completed, install the splashguards. Splashguards may be sealed to the floor using a vinyl cove base trim. The size of trim needed will depend on how much the floor is out of level.
-
Page 11: Electrical Specifications
Rev.0109 Electrical Specifications... -
Page 12: Case Schematics
IGIC-RMID-0109 CASE SCHEMATICS... - Page 13 Rev.0109 CASE SCHEMATICS (CONT’D)
- Page 14 IGIC-RMID-0109 CASE SCHEMATICS (CONT’D)
- Page 15 Rev.0109 CASE SCHEMATICS (CONT’D)
- Page 16 IGIC-RMID-0109 CASE SCHEMATICS (CONT’D)
- Page 17 Rev.0109 CASE SCHEMATICS (CONT’D)
- Page 18 IGIC-RMID-0109 CASE SCHEMATICS (CONT’D)
- Page 19 Rev.0109 CASE SCHEMATICS (CONT’D)
- Page 20 IGIC-RMID-0109 CASE SCHEMATICS (CONT’D)
- Page 21 Rev.0109 CASE SCHEMATICS (CONT’D)
- Page 22 IGIC-RMID-0109 CASE SCHEMATICS (CONT’D)
- Page 23 Rev.0109 CASE SCHEMATICS (CONT’D)
- Page 24 IGIC-RMID-0109 CASE SCHEMATICS (CONT’D)
- Page 25 Rev.0109 CASE SCHEMATICS (CONT’D)
- Page 26 IGIC-RMID-0109 CASE SCHEMATICS (CONT’D)
- Page 27 Rev.0109 CASE SCHEMATICS (CONT’D)
- Page 28 IGIC-RMID-0109 CASE SCHEMATICS (CONT’D)
- Page 29 Rev.0109 CASE SCHEMATICS (CONT’D)
- Page 30 IGIC-RMID-0109 CASE SCHEMATICS (CONT’D)
- Page 31 Rev.0109 CASE SCHEMATICS (CONT’D)
-
Page 32: Appendices
1.1 The installer is responsible for following the installation instruc- tions and recommendations provided by Hussmann for the installation of each individual type refrigerator. 1.2 Refrigeration piping should be sized according to Hussmann’s equipment recommendations and installed in accordance with normal refrigeration practices. Refrigeration piping should be insulated according to Hussmann’s recommendations. - Page 33 Rev.0109 Readings of return air temperatures will be variable and results will be inconsistent. The product temperature alone is not an indicator of refrigerator performance. NOTE: Public Health will use the temperature of the product in determining if the refrigerator will be allowed to display potentially hazardous food.
-
Page 34: Appendix D. - Recommendations To User
1.2 Load levels as defined by Hussmann must be observed. 1.3 The best preservation is achieved by following these rules: a) Buy quality products. - Page 35 Rev.0109 Depending on the amount of water, the temperature can drop 10° to 20° in as little as five minutes. 11. When transferring hot foods in the heated merchandiser to clean pans, preheat the clean pan. Transferring hot foods to room temperature pans can cause the temperature of the food to drop 20°...
- Page 36 IGIC-RMID-0109...
- Page 37 On Hussmann refrigeration systems, an additional (4) year extended warranty for the motor/compressor assembly is available, but must be purchased prior to shipment to be in effect. Hussmann reserves the right to inspect the job site, installation and reason for failure.
-
Page 38: Hussmann ® Chino 13770 Ramona Avenue • Chino, California
The MODEL NAME and SERIAL NUMBER is required in order to provide you with the correct parts and information for your particular unit. They can be found on a small metal plate on the unit. Please note them below for future reference. MODEL: SERIAL NUMBER: IGIC-RMID-0109...