Related Manuals for Fast Master Products SWIVELWHEEL-46
Summary of Contents for Fast Master Products SWIVELWHEEL-46
- Page 1 SWIVELWHEEL-46 OWNERS MANUAL & ASSEMBLY INSTRUCTIONS Fast Master Products, Inc. P.O. Box 654, Katy Texas 77492-0654 Tel: (281) 391-6750 Fax: (281) 391-6760 Email: info@cruiserlift.com web: www.swivelwheel.com...
- Page 2 SWIVELWHEEL-46 COMPONENTS Two Point Hook-Up Hitch Assembly ¾” Treated/Painted Optional Plywood Decking Spare Tire Front Support Mounts 2” x 2” ID Stake Bed Receivers 3” x 1” Rectangular Front Jack Stand Legs Steel Tubing Frame with Wheels Torsion Suspension and...
- Page 3 WHEN LOADED, THE DECK SHOULD BE LEVEL OR SLIGHTLY LOWER IN THE FRONT. NEVER COMPLY WITH STATE LOCAL PULL THE SWIVELWHEEL-46 SYSTEM WITH THE LICENSING AND REGISTRATION LAWS WHERE REAR DECK LOWER THAN THE FRONT, OR APPLICABLE. MORE WEIGHT TO THE REAR THAN THE FRONT. ALWAYS...
-
Page 4: System Specifications
SYSTEM LIGHTING: RUNNING LIGHTS, RT & LT TURN, STOP SPECIFICATIONS LIGHTS, & LICENSE PLATE LIGHTING. 4-WIRE FLAT TRAILER PLUG (STANDARD) 6-WAY ROUND to 4-WIRE FLAT ADAPTER (OPTIONAL) TOW VEHICLE: 7-WAY ROUND to 4-WIRE FLAT ADAPTER CLASS “A” DIESEL MOTOR COACH ... - Page 5 ASSEMBLY INSTALLING THE TORSION SUSPENSION The Swivelwheel-46 system is shipped to you unassembled to reduce the freight costs. These instructions will guide you through the assembly process. Once you receive the system, remove the components from the boxes. Lug Nuts 1.
- Page 6 TAIL LIGHT MOUNTING ADJUSTING THE FRICTION ROTOR ASSEMBLY 1. Install the lights to the rear of the trailer. The lights should be marked ALL SWIVELWHEEL SYSTEMS ARE “Passenger” and “Driver” side. If SHIPPED WITH A FRICTION ROTOR AND PAD not, the light with the clear bottom ASSEMBLY lens is always mounted on the driver side.
- Page 7 2. Insert the 5/8” x 4” Gr-8 mounting FRICTION PAD bolt with 5/8” lock washer from the FRICTION ROTOR passenger side, through the receiver and into the hitch insert. The insert is threaded about half way through. JAM NUT FRICTION PAD ADJUSTMENT BOLT 3.
- Page 8 You may have to adjust the deck a couple of times to get the correct position. Never have 1. Roll the swivelwheel-46 system up to the the rear deck lower than the front while hitch mount on the tow vehicle.
- Page 9 Adjustable Support Plate 2” x 2” Solid Steel Insert 5/8” x 3” Bent Hitch Pin with Hair Pin Cotter 5/8” x 4” Grade-8 Hex Bolt with Lock Washers and Nut...
- Page 10 OPTIONAL LOADING RAMPS 1. Lay the Loading Ramps out to the side or rear of the Swivelwheel-46 system as shown below. The two side ramps have red fingers that extend over the deck edge. The center ramp has an aluminum plate that extends over the deck edge.
-
Page 11: Maintenance
The top deck is painted with Black Premium Outdoor Gloss paint. The plywood used on the deck of the Swivelwheel-46 system is pressure treated. The bottom of the deck is not painted because it does not need to be. If you want to paint the bottom of the plywood you may do so. - Page 12 Fast Master occurred after the delivery date. Products, Inc, without written consent from Fast Master Products, Inc. will void the warranty and product liability insurance associated with that product. The Swivelwheel system was not designed •...
-
Page 13: Warranty Replacement Parts
Fast Master Products, Inc. management. Once the defective part has been returned to Fast Master Products, Inc, and found that it was a warranty issue, you will be credited for the charge.