Related Manuals for Fast Master Products SWIVELWHEEL-58
Summary of Contents for Fast Master Products SWIVELWHEEL-58
- Page 1 SWIVELWHEEL-58 OWNERS MANUAL /ASSEMBLY INSTRUCTIONS Fast Master Products, Inc. P.O. Box 654, Katy Texas 77492-0654 Tel: (281) 391-6750 Fax: (281) 391-6760 Email: info@cruiserlift.com...
- Page 2 SWIVELWHEEL-58 COMPONENTS ¾” Treated/Painted Plywood deck Standard Two Point Hitch Assembly Swivel Access Hatch Cover Optional Spare Tire & Wheel 2” x 2” ID Stake Bed Receivers 5.70 x 8 8-Ply, D-Rated, Highway Speed Trailer Tire & Torsion Suspension 3” x 1 ½” Rectangular...
- Page 3 WHEN LOADED, THE DECK SHOULD BE LEVEL OR LOWER RATED TIRE. SLIGHTLY LOWER IN THE FRONT. NEVER PULL THE SWIVELWHEEL-58 SYSTEM WITH THE REAR DECK COMPLY WITH ALL STATE AND LOCAL LICENSING LOWER THAN THE FRONT, OR MORE WEIGHT TO AND REGISTRATION LAWS WHERE APPLICABLE.
-
Page 4: System Specifications
7-WAY ROUND to 4-WIRE FLAT ADAPTER (OPTIONAL) TIE DOWN POINTS: SYSTEM SPECIFICATIONS VERTICAL POWDER COATED E-TRACK ON RIGHT AND LEFT DECK SURFACE TOW VEHICLE: A-TRACK TIE-OFF ADAPTERS. (OPTIONAL) CLASS “A” DIESEL MOTOR COACH CLASS “A” GAS MOTOR COACH ... - Page 5 5/8” x 3” Bent Hitch Pins. • the Swivelwheel-58 frame. Start a couple of lug nuts on the studs. You may now release the torsion suspension and it will stay in place.
- Page 6 TAIL LIGHT MOUNTING SAFETY CHAIN MOUNTING 1. Installing the lights to the rear of the trailer. The lights should be marked “Passenger” and Under and behind the front support mounts is a “Driver” side. If not, the light with the clear front to rear cross member.
- Page 7 There is an optional Dual Mount Hitch available for takes out any play within the hitch assembly. This mount includes two the Swivelwheel-58 system. additional 2” x 2” ID x 9” long receivers to be installed onto the tow vehicle.
- Page 8 Swivelwheel Mounting Deck Plates 1. Roll the swivelwheel-58 system up to the hitch mount on the tow vehicle. This should be done on level ground. 4. Raise one corner of the system to the closest upward hole position and insert the supplied 2.
- Page 9 5. Continue raising the deck sides until you achieve ASSEMBLY a deck position of slightly lower in the front than the back. In this position, when loading the Rotor Plate Friction Pad deck, the platform will lower slightly to a level position for travel.
- Page 10 1. Lay the loading ramps out to the side or rear of E-Track strips attached to the frame deck. These are the Swivelwheel-58 system as shown below. The usually attached to the right and left front sides of the two side ramps have red fingers that extend system unless otherwise requested.
-
Page 11: Maintenance
Check all tie-downs frequently. If using the stake bed receivers on the Swivelwheel-58 system: Do not hook the S-hook through the bottom of the holder. - Page 12 Fast Master Products, Inc, without of these are fast drying paints. If you get the enamel written consent from Fast Master Products, Inc. will void paints, expect to wait 24 hours to fully dry. the warranty and product liability insurance associated with that product.
- Page 13 Once the defective part has been returned noted upon delivery, note the damage on the to Fast Master Products, Inc, and found that it was a freight bill and contact Fast Master Products, warranty issue, you will be credited for the charge.