Related Manuals for Fast Master Products Swivelwheel-58DW
Summary of Contents for Fast Master Products Swivelwheel-58DW
- Page 1 SWIVELWHEEL-58DW OWNERS MANUAL /ASSEMBLY INSTRUCTIONS Fast Master Products, Inc. P.O. Box 654, Katy Texas 77492-0654 Tel: (281) 391-6750 Fax: (281) 391-6760 Email: info@cruiserlift.com...
- Page 2 SWIVELWHEEL-58DW COMPONENTS 2” x 2” Stake Bed Safety Chains ¾” Treated / Painted Receivers Plywood Decking Welded Tubular Steel Frame DOT required lighting w/ 4-wire flat plug Jack Stands with wheels for easy Torsion Suspension movement while with Friction disconnected from...
- Page 3 14. NEVER REPLACE THE SYSTEM TIRE (“C”) WITH CONNECTING TO AND DISCONNECTING FROM A LOWER RATED TIRE. THE TOW VEHICLE. COMPLY WITH ALL STATE AND LOCAL THE SWIVELWHEEL-58DW SYSTEM IS NOT LICENSING AND REGISTRATION LAWS WHERE INTENDED FOR SHORT-NARROW WHEEL APPLICABLE. BASE VEHICLES.
-
Page 4: System Specifications
TAHOE, SUBURBAN, ETC) TOW-VEHICLE MOUNTING: HITCH REQUIREMENTS: ONE PERSON, ADJUSTABLE HEIGHT, PIVOTING MOUNTING HARDWARE. THE SWIVELWHEEL-58DW SYSTEM SYSTEM INCLUDES A DUAL RECEIVER / REQUIRES THE USE OF DUAL POINT ROTATIONAL HITCH ASSEMBLY. RECEIVERS FOR OPTIMUM STABILITY. TWO ADDITIONAL RECEIVERS INCLUDED RECEIVERS ARE SPACED 30”... - Page 5 Wheel Hub Lug Nuts ASSEMBLY Remove the Swivelwheel-58DW system from the 4. With another person helping. insert the packaging and make sure that all components are swivel mount lug bolts from the bottom present. upward through the swivel box, and install a) 1ea Frame &...
- Page 6 THE TOW VEHICLE Passenger side light = Brown, Green, White 2. Replace the rear side decking to the The Swivelwheel-58DW utilizes a Dual Mounting system and tighten the screws. This mount includes two Rotating Hitch system. additional 2” x 2” ID receivers to be installed JACK STAND LEGS onto the tow vehicle.
- Page 7 Receiver 5/8” x 3” Bent Insert Hitch Pin w/ Hair Pin Cotter Hitch Pivot Point Hitch Pin Holes 5/8” x 3” Bent Hitch Pin w/ Hair Pin Cotter Adjustable Upright NOTICE YOU MUST OCCASIONALLY CHECK THE HITCH ASSEMBLY FOR TIGHTNESS. MAKE SURE THAT THE 1 ¼”...
- Page 8 The pivot in the Rotating Hitch assembly is being accomplished through a 1 ¼” bolt and Nylon nut. The nut is backed up with a lock nut. Between the front and rear hitch halves, there are three disks. Two are steel disks welded to the front and rear components.
- Page 9 Welded to the ends of the rear cross member there is a built in stop to the adjustable mounting plates as shown below. This stop restricts the movement of the rear cross member, while under a load, from allowing the rear cross member tube the ability to flex and touch the front tube.
- Page 10 ATTACHING THE SYSTEM TO ROT-HITCH BAR 1. Roll the swivelwheel-58DW system up to the hitch mount on the tow vehicle. 2. Line up the two Adjustable Mounting Plates with the center of the Front Support Brackets on the front of the Swivelwheel- 58DW trailer.
- Page 11 4. You may hear a slight squeaking noise when the wheel turns. This is normal due to the friction pad turning on the rotor plate. ADJUSTING THE FRICTION ROTOR ASSEMBLY ALL SWIVELWHEEL-58DW SYSTEMS ARE SHIPPED WITH A FRICTION ROTOR AND PAD ASSEMBLY FOR EACH TORSION SUSPENSION...
- Page 12 Swivelwheel system for strength. 1. Lay the loading ramps out to the side or rear of the Swivelwheel-58DW system as shown below. The two side ramps have red fingers that extend over the deck edge. The...
- Page 13 LOADING THE PLATFORM TYING DOWN CARGO ONTO THE 1. Always load and unload on level ground. A DECK good starting point is to level the deck on the hitch bar, then drop it down one hole so that the deck is slightly lower in the front When tying any cargo onto the deck, always make than the rear.
-
Page 14: Maintenance
I travel. I know that some highways have speed limits of 75 mph, but the trailer tire BEARINGS: Swivelwheel-58DW system’s manufacturers have told us that the majority of the wheel hub assembly should be inspected from time to trailer tires on the market today have a speed rating time to assure there is sufficient grease. - Page 15 Products, Inc, without written consent nonrefundable. from Fast Master Products, Inc. will void the warranty and product liability If a customer has any questions or • insurance associated with that concerns about installation please product. call Fast Master Products, Inc. at 1- 866-794-8357...
- Page 16 Modifications or changes made in any • product manufactured by Fast Master Products, Inc, without written consent from Fast Master Products, Inc. will void the warranty and product liability insurance associated with that product WARRANTY REPLACEMENT PARTS: •...