Advertisement
3
After loosening the wing bolt on the
RHH130, slide the RHH130 onto the hi-
hat stand shaft then set the RHH130
so that it is horizontal to the cymbal
support plate. Swivel the clamp base
up so that the hi-hat stand's vertical pipe
can be clamped between the clamp
base and open clamp. Then tighten the
nut to secure the clamp base.
* Make sure that the main unit is set horizontally in relation to the cymbal support plate. If not, the
RHH130 may not function properly, or cause the hi-hat shaft to bend.
4
Raise the clutch base to a suitable
height, and tighten the wing bolt to se-
cure the hi-hat shaft to the clutch base.
As the upper position of the clutch base
represents the open hi-hat position (the
space between the open cymbals), set
clutch base position according to your
playing style.
* Setting too wide of a stroke may result in the clutch base making contact with the top unit inside of
the cymbal pad and producing unexpected sounds while playing.
■ Connections
Using the two supplied stereo phone cables, connect the RHH130's output jacks to the
input jacks on your DTX Series Drum Trigger Module (DTXTREME/DTX/DTXPRESS).
First, connect the RHH130's [PAD] output jack to the module's [HI-HAT] input jack, then
the RHH130's [HI-HAT CONTROL] output jack to the module's [HI-HAT CONTROL] in-
put jack. The L-shaped connectors should be connected to the RHH130.
■ Troubleshooting
If the following trouble occurs when the RHH130 is used, please check the following
points before asking your dealer for assistance.
● No Sound, Volume is Low
Problem
Is the RHH130 properly con-
Refer to the previous [Connections] section and make sure
nected to the DTX Series Drum
that all connections are proper.
Trigger Module using the two
supplied stereo cables?
Is the Level Adjustment Screw on
If the Level Adjustment Screw is set too low, the single pro-
the RHH130 set too low?
duced by the pad will be too low to produce sufficient volume
from the drum trigger module's tone generator even though
the pad is struck.
Is the module properly con-
Check the connections between the external device and the
nected to a pair of headphones
position of the power switch and volume level.
or an external audio device such
as an amplifier, speaker, etc.?
Are module settings correct?
Check the volume setting of the voice assigned to the INPUT
number to which the RHH130 is connected (refer to the previ-
ous [Adjusting the Voice Volume] section), or make sure the
headphones volume level is not set too low, etc.
● Hitting the pad once produces multiple sounds (Double trigger)
Problem
Is the level adjustment on the
Too high of a the level adjustment setting causes the drum
RHH130 set too high?
module to produce multiple sounds because the large signal
produced by the high settings sustains for too long of a time.
Refer to the [Output Level Adjustment] section described
above to properly set the pad's output level.
● The edge and/or pad sections do not produce any sound. The Control Func-
tion does not function.
Problem
Is the RHH130 connected to the
Refer to the [Connections] section described above and make
proper INPUT number on the
sure that the RHH130 is connected to the proper INPUT num-
DTX Series Drum Trigger Module
ber on the module. The RHH130 will not operate using a
using the two supplied stereo
monaural cable.
cables?
Are module settings correct?
Refer to the section on trigger settings in the Owner's Manual
that came with your module and make sure settings are cor-
rect.
Setting Up
Wing Bolt
Hi-Hat Shaft
Cymbal Support
Plate
Clamp Base
Nut
Open Clamp
Raise
Hi-Hat Shaft
Wing Bolt
Clutch Base
Top Unit
Center Shaft
Nut
Nut
Open Clamp
Clamp Base
Output Jack
Insert
Insert
What to check
What to check
What to check
* The RHH130 incorporates switches in its edge and controller sections. Make sure that a stereo
cable is used when making connections between the RHH130 and the module. The RHH130 will
not operate using a monaural cable.
● Module Settings
The following changes to settings should be made according to the type of tone
module you are using. Please refer to the your tone module for further information.
II
DTXTREME
s
● Special settings are not required.
(The RHH130 is compatible with this
module's factory settings.)
The RHH130 is especially designed to take advantage of the powerful features offered
by the DTXTERME IIs and DTXPRESS III. The RHH130 can be used with the older
model tone modules listed below as long as changes to settings, also described below,
are made. However, be aware that the RHH130's performance will not be the same as
that with the DTXTREME IIs or DTXPRESS III.
For the modules listed below, first proceed with the setting in Step 1.
In some cases, cross-talk generated from a foot-closed sound may trigger a hi-hat sound even
though the setting in Step 1. has been carried out.If cross-talk is obvious, proceed to Step 2..
* Since the setting in Step 2. makes low velocity triggers harder to detect, we recom-
mend that you experiment with the setting's values to best match your playing style
and conditions.
II
DTXPRESS
1
. In the Utility Mode Hi-Hat Offset, set the
HH OffS value to "–5".
2
. In the Trigger Setup Edit Mode Gain,
Minimum Velocity, set the Gain to
"40%".
DTXPRESS
1
. In the Utility Mode Hi-Hat Offset, set the
HH OffS value to "–5".
2
. In the Trigger Setup Edit Mode Gain,
Minimum Velocity, set the Gain to "40%".
● A pad voice sounds when the foot is removed from the hi-hat pedal. (Noise)
Problem
Is the clutch base making con-
Check [step 4 in the Setup] section described above.
tact with the top unit inside of the
main unit?
Also, please refer to the Owner's Manual that came with your DTX Series Drum Trigger Module
(DTXTREME/DTX/DTXPRESS) for more information regarding the problems described above and any
other problems that you may be experiencing.
If a solution can not be found to the problem after consulting the manuals, please contact the dealer from
whom you purchased the product.
■ Specifications
● RH130 Real Hi-Hat Pad
Dimensions
ø329 x 106(H) mm (Clamp not included)
Weight
2.3kg (Clamp not included)
Sensor Type
Trigger Sensor (piezo-electric) x1/switch x1 (edge)
Controller Type
Multi-step Switch
Output Jacks
Standard Stereo Phone Jack x2
* Improvements may result in a change in the specifications and/or design of the product without notice.
SPECIAL MESSAGE SECTION
NOTICE: Service charges incurred due to a lack of knowledge relating to how a function or effect works (when the unit is operating as designed) are
not covered by the manufacturer's warranty, and are therefore the owners responsibility. Please study this manual carefully and consult your dealer
before requesting service.
ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our
products and the production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you
to be aware of the following:
Warning: Do not attempt to disassemble.
Disposal Notice: Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end, please
observe all local, state, and federal regulations that relate to the disposal of products that contain lead, plastics, etc. If your dealer is unable to assist
you, please contact Yamaha directly.
NAME PLATE LOCATION: The name plate is located on the bottom of the product. The model number, serial number, are located on this plate.
You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as a permanent
record of your purchase.
Model : RHH130
Serial No.
Purchase Date
PLEASE KEEP THIS MANUAL
Connections
III
DTXPRESS
● Set the Trigger Setup setting (refer to the
Owner's Manual that came with the
DTXPRESS III) to "4. SP Med."
DTXTREME
1
. In the Utility Mode [UT 7] SYSTEM3,
set the FCoffset value to "–5".
2
. In the Trigger Edit Mode TrgSens2 (trig-
ger sense 2), set the minimum level
to "20%".
DTXver.2
1
. In the Utility Mode 8.FC offset, set the
FCoffset value to "–5".
2
. In the Trigger Edit Mode 5. Level Range,
set the minimum level to "20%".
What to check
Printed in Indonesia
WF75970
Advertisement
