Hussmann IMPACT Excel C2-X Install Manual

®
Merchandisers
Multideck Merchandiser Joint Kit Instruction
PARTS LIST
Item Quantity
18 in. Front 22 in. Front 26 in. Front
1. 1 1 1
2. 1 1 1
3. 4 5 5
4. 4 5 5
5. 4 5 5
6. 1 2 2
7. 1 1 1
8. 2 2 2
9. 2 2 2
10. 1 1 1
11. 1 1 1
12. 4 4 4
Note:
Nut retainers are factory installed in the left end, and alignment pins are factory installed in the right end of each merchandiser.
NOTE: Be sure Merchandisers have Apply Gasket – 1 in the
2
been leveled according to the instal- horizontal recess across the
lation instructions. Be sure factory- bottom and up front to cover
installed nut retainers and align- slots, including glass front.
ment pins are in place. Apply Gasket – 2 to cover
foam-to-metal gap at rear and
1 Remove shelves (if installed),
across top as shown. Lap gas-
display racks, pans, front shelf
kets at lower corners. Check
supports and front air grilles
that there are no gaps between
from the right end.
gasket and merchandiser.
Remove the rear panels from
• Do not stretch gasket,
the right end:
especially around corners.
• Do not butt gaskets; always
A. Remove the lower back
overlap joints.
panel first by lifting up from its
• Remove paper backing after
bottom edge and out. Do not
gasket is applied.
use sharp tools.
B. Lift the upper back panel
3 Move second Merchandiser
up and out.
against first, mating
alignment pins with
corresponding holes.
Fasten fronts together using
4
Cap Screw – 3, Flat
Washers – 4, Lock
Washers – 5, and Nut – 6.
Tighten only until front panels
touch. Do not tighten fully.
Removing Back Panels
Description
Gasket 1 / x 1 / x 60
2 2
Gasket 1 / x 1 5 / x 120
2 8
Cap Screw 5 / -18 x 1 1 /
16 4
Flat Washer 5 /
16
Lock Washer 5 /
16
Hex Nut 5 / -18
16
Threaded Rod 1 / -16 x 12
2
Flat Washer 1 /
2
Hex Nut 1 / -16
2
Butyl Tape
Splashguard Joint Support
Hex Head Sheetmetal Screw #8 x /
1
2
Use Cap Screws – 3 with Flat
5
Washers – 4 and Lock
Washers – 5 to draw
merchandisers together at rear.
Start at the bottom, below the
coil baffle, then middle, then
top; tighten until gaskets are
compressed.
Draw canopies together using
6
Rod – 7 through top shoe, and
Washers – 8, and Nuts – 9 on
each end of rod. Stop when
canopies touch.
Apply Butyl Tape – 10 across
7
bottom joint, extending up
at back and front. Use field-
supplied silicone in any gap
between front support brackets.
Splashguard
brackets
MUST BE
INSTALLED
BEFORE
PIPING CASE.
S
T
1
/ in. Gasket
2
E
P
5
1 / in. Gasket
8
2
E
S
Butyl Tape
T
E
Silicone
P
1 7 8
(field supplied)
7
High
Front
Detail
3
A
1
Glass
Front
Alignment
Detail
Bullets
6
3 4 5
9
8
7
11
8
9
Connecting Canopies
Splashguard Joint Support
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.)
Refer to I/O manual to install
8
splashguard brackets.
2
Install Splashguard Joint
Support – 11 using
Screws – 12. Install splash-
D
guards and lower front panels
according to I/O manual.
9
9 Refer to Poster 389043 or
2
I/O manual or to remove and
install top rail and bumpers.
3 4 5
Install upper bumper starter and
bumper trim butted up to left end.
C
Push into place. Slide internal
bumper trim under right end of
upper bumper starter. Install full
6
4 5
length bumpers and trim flush
2
with starter and offset across
joints, making sure no gaps exist
between sections. Push into place.
10
Install lower bumper starter butted
B
up to left end. Push into place. Add
full length bumpers flush with
starter and offset across joints,
making sure no gaps exist between
1 sections. Push into place.
Install top rail starter butted up to
left end; push front down over
color panel until snap, then push
10
rear over light chanel until snap.
Add full length top rail flush with
starter and offset across joint.
R
EFRIGERATE CASE LINEUP AND LAST
Butyl
SECTIONS FOR AT LEAST
Detail
Before installing last sections, tap
the right end of top rail and
bumpers to close any gaps.
Measure between right end and
installed rail or bumper. Use a
miter box and fine-toothed saw
to cut last bumpers to length.
Before installing last section of
upper bumper, install internal trim
flush to right end, then install cut
bumper.
12
Installing
Installing Splashguard
6 .
HOURS
September, 1995
P/N 0376449C