Advertisement
Quick Links
Nitrogen Tyre Inflator
Vacuum
Inflation System Main Features:
■ Pump the air from the tyre by the internal vacuum generator *
■ Auto-Start Inflation *
■ Single Tire Application
■ Suit for: Motorcycle,Car, Light Truck
PN-8820
Operation Steps
1.Set final target pressure using the + and - buttons. The upper LED
screen will show the target pressure.
2.Set the vacuum time using the + and - buttons. The lower LED screen
will show the vacuum time.
3.Lift the vehicle to avoid demage to the tyre due to the heavy vehicle
weight.
4.Remove the tyre valve core to exhaust the residual air from the tyre,
Then refit the tyre valve core.
5.Connect air hose to tyre valve stem.
6.Press"START"key.
7.When unit "beeps" and the upper LED screen flashes "END", tyre
inflation is complete.
8.Immediately remove hose.
Model
Nitrogen
1
Nitrogen
Tyre
Model: PN-8820
Tyre
Inflator
Advertisement
Related Manuals for Priman PN-8820
Summary of Contents for Priman PN-8820
- Page 1 Nitrogen Tyre Inflator Model: PN-8820 Vacuum Model Nitrogen Tyre Inflation System Main Features: ■ Pump the air from the tyre by the internal vacuum generator * ■ Auto-Start Inflation * ■ Single Tire Application ■ Suit for: Motorcycle,Car, Light Truck...
- Page 2 Nitrogen Tyre Inflator Model: PN-8820 1.0 Introduction 1.1 This Manual Congratulation on selecting the tire Inflation Equipment.This equipment has a number of unique features that are explained in this manual. Throughout the manual the following symbols will be used, this information is for your safety and to prevent damage to this product.
- Page 3 Nitrogen Tyre Inflator Model: PN-8820 2.0 Control Layout A: Inlet of compressed air and regulator B: Hours run C: System pressure gauge: Indicate the compressed air inlet pressure D: Nitrogen pressure gauge E: Power cable F: Power switch G: Automatic nitrogen inflation outlet...
- Page 4 Nitrogen Tyre Inflator Model: PN-8820 2. Connect the compressed Air supply to the Inlet of compressed air (A) located in the regulator. The inlet regulator should be set at 123PSI/8.5bar/850kPa 3. Connect the Hose with single clip-on open type chuck to AutomaticCnitrogen inflation outlet (G) located in the unit 4.
- Page 5 Nitrogen Tyre Inflator Model: PN-8820 4.0 Operation 4.1 Manual inflation by the Black Clip-on deflator&inflator To increase the purity of the nitrogen in the tire the air must be removed. 4.1.1 Air extraction 1. Connect 0.7m hose (J) to the tire.
- Page 6 Nitrogen Tyre Inflator Model: PN-8820 4.2.2 Nitrogen Filling of the New Tire 1. A choice between bar, PSI, Kgf/cm2 and Mpa on the keypad is available by pressing the white ‘C arrow key’ before preferred choice. 2. Press the time setting key ‘∇’ or ‘∆’ for purge/vacuum cycle. The default value of the machine is 20 seconds and the user can increase or decrease this setting according to the tyre size.
- Page 7 Nitrogen Tyre Inflator Model: PN-8820 5.0 The Pressure Calibration Procedures To the automatic tyre nitrogen inflators, when the users found the inflator accuracy is higher than 1.5PSI / 0.1bar / 0.01Mpa / 0.1Kgf/cm2, they can calibrate the unit by the following methods.
- Page 8 (A),then insert it to the kick 4 and kick 5 of accessory (B).Turn on the power again. 9 .The calibration is over. Producer: ZHUHAI PRIMAN AUTO MAINTENANCE EQUIPMENT CO.,LTD ADD: 2# PLANT, MINGHONG INDUSTRY BASE, LIANGANG INDUSTRIAL ZONE ZHUHAI CITY, GUANGDONG PROVINCE P.R. CHINA TEL:86-756-7799055 FAX:86-756-6210996 EMAIL:zhpriman@zhpriman.com...