Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Krenn KRC 8
- Page 1 PNEUMATIC REBAR CUTTER MODEL: KRC 8 / KRC 8 L INSTRUCTION MANUAL...
-
Page 2: Table Of Contents
2.1 Composition of the Cutter 2.2 Preliminary Operating Procedure 2.3 Operation of the Cutter Inspection and Maintenance 3.1 Maintenance 3.2 Blade Replacement Technical Specification KRC 8 / KRC 8 L with head Spare parts list KRC 8 / KRC 8 L... -
Page 3: Introduction
Introduction You are now in possession of a Steel Cutter Model KRC. This machine has been designed and manufactured in accordance with modern and reliable technology. In order that you may enjoy the reliability of the cutter for a long time and to ensure that a safe operation of the material can be guaranteed, it is absolutely necessary to read this instruction manual thoroughly and to observe strictly the instructions given therein b e f o r e starting the operating procedure. -
Page 4: Safety
Safety 1.1 Possible Dangers operating the Machine The Steel Cutter Model RC has been manufactured according to the latest technical knowledge and is operationally reliable. A functional and safety test has been carried out. In spite of this fact, it is possible that certain dangers are imminent if the cutter is not being operated by trained personnel or at least personnel who has received relevant instruction on the operation. - Page 5 (Safety Instructions continued) • During the work with the cutter, always see to it that your position is safe and upright. Avoid any abnormal position of your body and do always keep your balance. • Whenever you use the cutter, inspect it as to any damages. If damages on the cutter are being found, you are not allowed to use it anymore.
-
Page 6: Defined Use
1.3 Defined Use The Steel Cutter Model KRC has been designed and manufactured in order to cut steel bars, steel profiles as well as constructional steel. The steel cutter is destined for industrial purposes and applications. The manufacturer is not undertaking any liability if the cutter is used for purposes and applications which are not mentioned in this instruction manual. -
Page 7: Start And Operation
Start and Operation 2.1 Composition of the Cutter 16 Pneumatic Air Connection 15 First Handle 7 Second Handle 1 Cutter Head 21 Trigger 7 Suspension Device 2.2 Preliminary Operating Procedure The cutter may be fastened by means of the suspension device (7) thus enabling the stationary operation. -
Page 8: Inspection And Maintenance
Inspection and Maintenance 3.1 Maintenance Owing to the modern Pneumatic Technique, the cutter is maintenance-free. If any defects should appear, please contact the manufacturer. Lubricate blade head friction areas every 500 cuts. Dip it in lubricating oil and pull the trigger several times keeping the blades By installing a device to remove in the oil. -
Page 9: Blade Replacement
3.2. Blade Replacement 1 TO PREVENT ANY ACCIDENTS KEEP AIR SUPPLY DISCONNECTED THROUGHOUT THE WHOLE BLADE REPLACEMENT OPERATION 2 REMOVE THE TWO FORK BOLTS. LOOSEN THE BOLTS AND REMOVE THE TWO HEAD AXLES BY PUTTING IT ON A FLAT SURFACE AND HITTING THE THREAD AREA WITH A NYLON HAMMER, NOT TO DAMAGE THE THREAD. -
Page 10: Technical Specification
7 Lt./cut at 7 bar MAXIMUM Ø CUT 8 Ø (Steel up to 70 kg/mm²) 6 Ø (Steel up to 180 kg/mm²) SPEED 60 Ø Cuts/minute MAXIMUM PRESSURE 8.5 bar MINIMUM PRESSURE 6 bar WEIGHT 5.8 kg (KRC 8) 7.2 kg (KRC 8 L) -
Page 11: Krc 8 / Krc 8 L With Head
Parts-List for Model KRC 8 / KRC 8 L Remarks Code-No. Part name / Description Unit 1 M60AS Set of blades asymmetric 1 M60L Set of blades 2 7001 Front axle 3 7002 Rear guide support KRC 8 3 8L002... - Page 13 KRC 8 / 8 L...