Using Your Beer Dispenser; Tap Equipment And Assembly - Fisher & Paykel DCS RF24BTL1 Installation, Operation And Maintenance Instructions

US
CA
This beer dispensing unit will support
rel. The double draft tower units can support two sixth (
barrels of beer. See chart below for quantity of beer in each
barrel size.
1/6 barrel
23
Height
(59.2 cm)
9
Diameter
(23.5 cm)
Gallons 5.16
#12 ounce
60
Glasses
Keg Size
5 gallon Corny
1/6 barrel
1/4 Barrel
1/2 Barrel

Tap Equipment and Assembly

Your dispensing kit includes the following parts:
Polished stainless steel tower with clear beer line (single
or double dispense)
Tower Gasket
Phillips oval head screws
Knob for Tower (Faucet Handle)
Keg coupler(s)
CO regulator with red gas line(s) attached
2
Empty 5 pound CO
2
Plastic clamp(s) large and small
Faucet wrench

USING YOUR BEER DISPENSER

⁄ barrel or
1
2
Barrel Sizes
1/4 Barrel 1/2 Barrel
⁄ " 14 ⁄ "
5 13
16 16
(37.6 cm) (59.2 cm)
⁄ " 17" 17" to 17
1
4
(43.2 cm) (43.2 to 43 cm)
7.75
82
Table A
#of kegs per
5 pound CO Tank
2
15 to 22
14 to 21
10 to 14
5 to 7
Table B
tank
Tools required for installation:
⁄ bar-
1
4
⁄ )
Flat bladed screwdriver
1
6
Phillips screwdriver
Pliers
Adjustable wrench or a 1
⁄ " open end wrench
1
2
23 ⁄ "
5
16
⁄ "
1
4
15.5
163
CO can be dangerous. If it becomes difficult to
2
breathe and/or your head starts to ache, a high
concentration of carbon dioxide may be present.
Leave the area immediately.
• The CO
regulator. Never connect the tank to the keg.
• The CO
upright position. Secure it with the chain pro-
vided.
• Never drop or throw the CO
• Keep the CO
• Ventilate the area after a CO
1. Remove shelving and packaged components from the
interior of the refrigerator before beginning the assem-
bly process.
2. Take your empty 5 pound CO
supply dealer to be filled. You can usually find them in
your "yellow pages" under "Welding Supply" or "Fire
Protection". One 5 pound tank can process many kegs
(see table "B") Your dealer should supply you with a
new plastic washer every time the tank is filled. This
washer is used at the regulator to tank connection. See
Figure 15 and 22 on page 11. Replace the old washer
with the new one whenever the tank is refilled.
3. Tower mounting (if you are installing the unit under a
counter skip to step 4). If you are mounting the tower
directly to the top of the refrigerator, first remove the
four screws from the top of the refrigerator. Remove the
foam plug from the large hole in the top of the refrigera-
tor. Feed the clear beer line through the tower gasket
and the large hole in the refrigerator top. Align the 4
holes in the tower with the 4 holes in the refrigerator
top and secure the tower with the 4 screws removed
previously. Skip to step 5.
10
⁄ " open end wrench
1
8
WARNING
!
tank must always be connected to the
2
tank must be securely mounted in the
2
tank.
2
tank away from heat.
2
leak.
2
tank to your local gas
2