Related Manuals for Fisher & Paykel CI302DTB3
Summary of Contents for Fisher & Paykel CI302DTB3
- Page 1 INDUCTION COOKTOP CI302DTB3, CI603DTB2, CI604DTB3, CI754DTB2, CI905DTB2 & CI905DTB3 models INSTALLATION GUIDE NZ AU GB IE SG 590492G 09.18...
-
Page 3: Safety And Warnings
SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS WARNING! Electrical shock hazard Particular attention shall be given to the relevant Disconnect the appliance from the mains ● requirements regarding ventilation. electricity supply before carrying out any work Read these instructions carefully before installing this or maintenance on it. - Page 4 SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Before you install the appliance, please make sure that if the cooktop is installed above an oven, the oven has a ● a suitable disconnection switch is incorporated in the built-in cooling fan. ●...
-
Page 5: Parts Supplied
PARTS SUPPLIED Foam tape (1) Clamping brackets (4) and screws (4) CI302DTB2 only Clamping brackets (2) and screws (2) Installing multiple products Note: We recommend installing products in separate cutouts with a minimum distance of 5 mm between the glass edges. ●... - Page 6 PRODUCT & CABINETRY DIMENSIONS Note: Electrical connection is made at the right rear FRONT REAR SIDE CI302DTB CI603DTB CI604DTB CI754DTB CI905DTB PRODUCT AND CABINETRY DIMENSIONS Overall height of product (including terminal block below top of chassis) Overall width of product Overall depth of product Height of chassis (including terminal block below top of chassis)
-
Page 7: Clearance Dimensions
CLEARANCE DIMENSIONS min. 4 mm min. 75 mm Drawer or other obstruction 20 mm Ventilation gap must be present Alternatively 2x 50mm holes in side wall to allow adequate cool air min. 4 mm Some ovens require installation in a sealed Oven with cooling fan box. - Page 8 FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED) Note: Electrical WARNING! connection is made at the right rear We do not recommend flush mounting and sealing as servicing requires the cooktop to be removed from the benchtop. The owner carries all risk for flush mounting the cooktop. The owner must ensure the cooktop has been cut out from the benchtop before servicing can be carried out.
- Page 9 FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED) ROUTER THE BENCHTOP TO THE SPECIFIED DEPTH FIT THE CLAMPING BRACKETS MASK OFF THE AREA TO BE SILICONED No. of brackets and slot positions depends on model view from below 12-40mm 40mm+ 5 mm Fit a minimum of 2 brackets on opposing sides IF REMOVING PRODUCT, CUT APPLY SILICONE WIPE OFF EXCESS SILICONE...
- Page 10 DISCARD PACKAGING PLACE COOKTOP UPSIDE DOWN IMPORTANT! - To avoid damage to the glass, ensure there is a protective cover underneath it. Recycle responsibly APPLY ADHESIVE FOAM TAPE AROUND GLASS EDGE LOWER GENTLY INTO THE CUTOUT Foam Tape 1 Apply the foam seal around the glass overhang, 5 mm in from the edge Adhesive side of the glass, with the adhesive side...
-
Page 11: Connecting The Cooktop To The Mains Power Supply
IMPORTANT! Connection diagrams This cooktop must be connected to the mains power supply only by a suitably qualified ● CI302DTB3, CI603DTB2, CI604DTB3, CI754DTB2 person. To connect the cooktop to the mains power supply, do not use adapters, reducers, or ●... -
Page 12: Final Checklist
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Is the cooktop earthed? Have you demonstrated the basic operation to the customer? Check that there is an adequate and constant flow of cool air from the cabinetry to the Make sure you explain to the customer about base of the cooktop. - Page 16 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2018. All rights reserved. The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available.