Table of Contents
Advertisement
Quick Links
QUICK GUIDE for Piccolo Light/multiGuard Master RF
Installation
1. Piccolo Light/multiGuard Master RF can be installed without using communication via the mobile
network, but if a SIM card is installed in the unit you will be able to receive alarms as text message
and email. You will also be able to perform set-up and service via the Profort web-service or via
your mobile phone.
2. Prepare a SIM card so that the PIN code is 1234 or deactivated and test if text messages can be sent
or received. Mount the card in the unit. The unit now has password 1234 or runs without a password.
The card is inserted as shown below.
3. Mount the unit near the security staff and as high and free as possible (never in a steel cabinet).
4. Connect inputs, outputs and power cable (230V/12-24V AC/DC). If necessary a rechargeable 9V
battery.
5. Turn on the power. A lengthy 'beep'will sound and the display shows: "BUSY..." After approx. 20
secs. 4 'beeps' will sound. The display now shows: "NO ALARMS".
Piccolo Light/multiGuard Master RF interior
DIP-switch for analog input
1 ON:
0-10 VDC
2 ON:
0/4-20 mA
3 ON:
PT-100
4 ON:
Profort temp. sensor
All OFF:
digital input
Ver. 1.03
Voltage
Output:
Input, digital: max. 24 VDC
Input, analog: max. 0-10 VDC
www.profort.com
AC max. 230 VAC, 6A
DC max. 30 VDC, 6A
max. power 2 mA
Only connect voltage when
DIP-switch 1 is on, og 2-4 are
off
Pg.
1
Advertisement
Table of Contents
Related Manuals for Profort Piccolo Light
Summary of Contents for Profort Piccolo Light
- Page 1 SIM card is installed in the unit you will be able to receive alarms as text message and email. You will also be able to perform set-up and service via the Profort web-service or via your mobile phone.
- Page 2 4. Create a new device in the list and select Piccolo Light/multiGuard Master RF. When you press SAVE, the portal sends a text message to the unit that connects it to the Profort server via mobile data on the SIM card. All additional settings are then sent as data.
- Page 3 Enter the 'ON / OFF' menu and touch the zone to be switched on or off. Pressing '0-7' will switch all zones on and off at once. In the bottom row you can see which zones are active. www.profort.com Ver. 1.03...
- Page 4 If an alarm is triggered on a detector, an alarm will appear in the display that shows the information on the current.alarm. If you want to reset the alarm, press 'Menu' followed by 'Reset alarm'. Now the screensaver will appear. For additional help: see the manual on www.profort.dk www.profort.com...
- Page 5 Piccolo Light with PoE interface for external alarm receivers Piccolo Light is available in a version with the option of external alarm receivers via PoE interface. Up to 6 external alarm receivers can be connected. These are connected as shown below: www.profort.com...
- Page 6 Piccolo Light must be restarted after mounting external alarm receivers. Make sure that the ip-addresses of the units are correct. The ip-address of the PoE interface inside the Piccolo Light must be the ‘master’ and all the ip-addresses of the external alarm receivers must respond back to this one.
- Page 7 SET-UP If Piccolo Light is set to monitor the wireless detectors and alarm receiver and no signals are received for 30 minutes, Piccolo Light will issue a 'warning' on the current unit. 'Warning' will be displayed in the alarm image and stored in the log.
- Page 8 Min. 18V max 30 V (24V DC) Inputs, analog 0-10V DC 0/4-24mA PT-100 Profort temperature sensor (007995) Wireless detectors Max. no. of wireless detectors: 126 Max. no. of analog climate detectors: 32 Serial connections RS232 for setup or connection to e.g. PLC Modbus for external units, e.g. energy meters Counter Max.
Need help?
Do you have a question about the Piccolo Light and is the answer not in the manual?
Questions and answers