Sign In
Upload
Download
Table of Contents
Contents
Add to my manuals
Delete from my manuals
Share
URL of this page:
HTML Link:
Bookmark this page
Add
Manual will be automatically added to "My Manuals"
Print this page
×
Bookmark added
×
Added to my manuals
Manuals
Brands
MAHLE Manuals
Diagnostic Equipment
TechPRO OBD-II Smartbox
Operation manual
MAHLE TechPRO OBD-II Smartbox Operation Manual
Hide thumbs
1
Table Of Contents
2
3
4
5
6
7
8
9
10
11
12
page
of
12
Go
/
12
Contents
Table of Contents
Bookmarks
Table of Contents
Table of Contents
Information
Document Warnings
Important Notes
User Group
Agreement
Product Description
Application
Scope of Delivery
Specifications
Product Use
Test OBD-II Port before Plug in Scantool
Test Without Ignition Key
Test with Ignition Key in on Position
Test with Engine Running
Monitor Voltage During Reflash Programming
Detect Communication Protocol
As Break out Box
Check Alternator Condition
As Power Backup for ECU While Replacing Car Battery
As DC Power Source for Other Devices
Notes
Advertisement
Quick Links
Download this manual
MAHLE TechPRO
OBD-II Smartbox
®
Operation Manual
EN
OBD-II Diagnostics
Table of
Contents
Previous
Page
Next
Page
1
2
3
4
5
Advertisement
Table of Contents
Related Manuals for MAHLE TechPRO OBD-II Smartbox
Diagnostic Equipment MAHLE RemotePRO User Manual
Remote diagnostics (37 pages)
Summary of Contents for MAHLE TechPRO OBD-II Smartbox
Page 1
MAHLE TechPRO OBD-II Smartbox ® Operation Manual OBD-II Diagnostics...
Page 2: Table Of Contents
Test with ignition key in ON position 3.1.3 Test with engine running Monitor voltage during reflash programming Detect communication protocol As break out box Check alternator condition As power backup for ECU while replacing car battery As DC power source for other devices Notes © MAHLE...
Page 3: Information
Contact Warning Consequences of hazard in the event of failure to MAHLE if you detect a problem that you cannot solve with this symbol observe action and information given. manual.
Page 4: Product Description
When the battery falls below 11.8V for 12V system or 23.8V for 24V system, the alarm will come on. In this case, you may need to start the engine to run for some time to charge the battery or replace with a new battery and then test again. © MAHLE...
Page 5
(The ‘Caution – Check’ LED will illuminate). communication signals or voltage output to the rest of the pins except pin 4 which is chassis ground and pin 16, the positive power output supplied from the battery direct. © MAHLE...
Page 6: Test With Ignition Key In On Position
If there is 12V present– the LED will blink slowly at interval of 1 sec danger but served as a warning. between each blink. (The ‘Caution – Check LED will illuminate). If there is 24V present – the LED will blink fast. (The ‘Caution – Check LED will illuminate). © MAHLE...
Page 7: Test With Engine Running
Under normal conditions when after all the testing of the vehicle DLC port has been done, where there are no abnormal activities, the green ‘OK’ LED will light up. This indicates everything is OK and it is ready for Scan tool to be plugged in. © MAHLE...
Page 8: Detect Communication Protocol
LIVE DATA. This will lead in a constant data stream between the scan tool and the vehicle, and then you can locate the LEDs that are flashing. © MAHLE...
Page 9: As Break Out Box
The voltage should above 13.6 Volts for 12V system and 27.6V for 24V system. If the voltage is below, check for loose drive belt and the Alternator. Fig. 4: Blink code cable for OBD-II Smartbox © MAHLE...
Page 10: As Power Backup For Ecu While Replacing Car Battery
4. After job done, remove the battery clips from the external battery, unplug OBD-II Smartbox from the car. The data saver cable comes with surge voltage protection, short circuit and polarity protection. © MAHLE...
Page 11: Notes
Notes | OBD-II Smartbox | 11 OBD-II Smartbox | 11 | 11 Notes © MAHLE...
Page 12
MAHLE Aftermarket Inc. 10 Innovation Drive York, PA 17402 717-840-0678 www.servicesolutions.mahle.com...
Table of Contents
Print
Rename the bookmark
Delete bookmark?
Delete from my manuals?
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL