Front-Panel Controls - Harman Kardon AVR 7200 Owner's Manual

1 3
4
2
1 Main Power Switch
2 System Power Control
3 Power Indicator
4 Headphone Jack
5 Tone Mode
6 Speaker Selector
7 Surround Mode Group Selector
8 Surround Mode Selector
9 Tuning Selector
)
Button
‹
! Tuner Band Selector
1 Main Power Switch: Press this button to apply
power to the AVR 7200. When the switch is pressed
in, the unit is placed in a Standby mode, as indicated
by the amber Power Indicator 3 surrounding the
System Power Control 2. This button MUST be
pressed in to operate the unit. To turn the unit off and
prevent the use of the remote control, this switch
should be pressed until it pops out from the front
panel so that the word "OFF" may be read at the top
of the switch.
NOTE: This switch is normally left in the "ON" position.
2 System Power Control: When the Main Power
Switch 1 is "ON, " press this button to turn on the
AVR 7200; press it again to turn the unit off. Note that
the Power Indicator 3 surrounding the switch will
turn green when the unit is on.
3 Power Indicator: This LED will be lit in amber
when the unit is in the Standby mode to signal that the
˘
¯
5 7 9
6
8
@ Set Button
#
Button
›
$ Preset Station Selector
% Input Source Selector
^ Tuner Mode Selector
& Optical 3 Digital Input
* Input/Output Status Indicator
( Coaxial 3 Digital Input/Output
Ó Video 4 Input/Output Jacks
Ô Bass Control
 Balance Control
unit is ready to be turned on. When the unit is in oper-
ation, the indicator will turn green.
4 Headphone Jack: This jack may be used to listen
to the AVR 7200's output through a pair of headphones.
Be certain that the headphones have a standard
stereo phone plug. The main room speakers will
automatically be turned off when the headphone jack
is in use.
5 Tone Mode: This button allows you to remove the
tone controls (Treble, Bass and Balance) from the signal
path. The first press of the button displays a TONE
IN message in the Main Information Display ˜.
If you wish to set the tone controls to "flat, " without any
treble or bass alteration, press the
Buttons )# so that TONE OUT appears in
the Lower Display Line B.
6 Speaker Selector: Press this button to begin the
process of configuring the AVR 7200 for the type of

FRONT-PANEL CONTROLS

FRONT-PANEL CONTROLS
˜
ˆ
! # % &
@ *
) $ ^
1 / "
4
‹ ›
or Selector
ı
Ò
25
Ú
26
( Ô
Ó 
Ò Treble Control
Ú Channel Adjust Selector
Û Delay Adjust Selector
Ù Digital Input Selector
ı Volume Control
ˆ Input Indicators
˜ Main Information Display
¯ Remote Sensor Window
˘ Surround Mode Indicators
speakers it is being used with. For complete informa-
tion on configuring the speaker settings, see page 21.
7 Surround Mode Group Selector: Press this but-
ton to select the top-level group of surround modes.
Each press of the button will select a major mode
grouping in the following order:
Dolby Modes _ DTS Digital Modes _ VMAx Modes
_ DSP Modes _ Stereo Modes _ Logic 7 Modes
Once the button is pressed so that the name of the
desired surround mode group appears in the on-screen
display and in the Lower Display Line B, press the
Surround Mode Selector 8 to cycle through the
individual modes available. For example, press this but-
ton to select Dolby modes, and then press the
Surround Mode Selector 8 to choose from the var-
ious mode options.
FRONT-PANEL CONTROLS 5 5