Harman Kardon AVR 65 Owner's Manual page 32

1. Press the button
f
Multi
the multiroom system. If the semi-OSD
system is engaged, a message will
appear at the bottom of the screen. If
the full-OSD system is engaged, the
complete multiroom menu (Figure 9)
will be shown on the video display.
Press the button within five
i
Set
seconds to enter the multiroom menus.
M U L T I R O O M : O F F
M U L T I I N P U T : C D
D V D
V I D E O
V I D E O
V I D E O
T U N E R
T I M O N
M U L T I L E V E L :
Figure 9
2. Press the or buttons
⁄ ¤
the multiroom system on or off, as
indicated by the front panel
Information Display message, the
semi-OSD message, or the change in
the highlighted video in the full-OSD
screen. Press the button
Set
enter the settings.
3. Within five seconds, press the
buttons to scroll through the
g
inputs. When the input source you wish
to send to the remote room location
appears on the front panel Information
Display, in the lower screen semi-OSD
message, or is highlighted in reverse
video in the full-OSD listing, press the
button to enter the selection.
i
Set
AVR65 120 volt Rev (C) 10/6/98
Multiroom Operation
to initiate 4. Within five seconds, press the
buttons
g
for the multiroom feed. The volume
change will appear as a number in dB
increments below the 0dB reference
level in the front panel Information
Display, as a lower third semi-OSD
message, or as the last line in the
full-OSD status display.
5. Press the
Set
O N
setting. If no further buttons are
pressed within five seconds, the unit
1
2
will return to normal operation.
3
2 0 D B
Multiroom Operation
Multiroom operation is simple, and it
may be controlled from either the main
listening room where the AVR65 is located,
or from a remote room when an optional
g to turn
IR sensor is connected to the
on the rear panel.
c
To activate the feed to the remote room,
press the
Multi
front panel or remote. Next, press the
to
i
or buttons
⁄ ¤
buttons
Selector
until the
MULTI
or
⁄ ¤
in the front panel Information Display.
Press the
Set
the setting.
When the multiroom system is turned on,
the previously selected input will be fed to
the
Multi Out
The volume will be as set in the previous
selection, although it may be further
adjusted using an optional volume con-
trol in the remote location or on the
optional audio power amplifier connected
to the
Multi Out
32
or
⁄ ¤
to change the output level
button i to enter the
jack
Multi
button on the
¯ f
on the remote or the
g
on the front panel
¸
indicator K illuminates
button to enter
i ˜
jacks on the rear panel.
d
jacks .
d
If an optional IR sensor is located in the
remote room and connected to the
AVR65's Multi IR jack, the multiroom
system may be turned on or controlled by
simply pointing the AVR65 remote, or an
optional programmable remote that
includes codes for the AVR65, at the IR
sensor. Note that depending on the type of
programmable remote used, it is probable
that the code for the Multi button will not
be contained in the pre-programmed
code library, and must be "learned" into
the remote, if possible.
To change the input source for the source
to the multiroom feed once it has been
turned on, follow the instructions shown
above in the Multiroom Setup section of
this manual.
Once the multiroom system is turned on,
it will remain on even if the AVR65 is
placed in the Standby mode in the main
room by pressing the
AVR Selector a
or the
System Power Control 2
the front panel. To turn the multiroom
system off, press the button
Multi
, and then the or buttons
f
⁄ ¤
on the remote or the
Selector
on the front panel until the
¸
indicator goes out. Press the
K
button i ˜ to enter the setting.
on
¯
g
buttons
MULTI
Set