Table of Contents
Advertisement
Speaker Configuration
The first few adjustments tell the AVR65
which type of speakers are in use. This is
important as it adjusts the settings that
determine which speakers receive low-
frequency (bass) information. For each
of these settings use the
LARGE
if the speakers for a particular position
are traditional full-range loudspeakers
that are capable of reproducing sounds
below 100Hz. Use the
SMALL
smaller, frequency-limited satellite
speakers that do not reproduce sounds
below 100Hz. Note that when "small"
speakers are used, a subwoofer is
required to reproduce low-frequency
sounds. Remember that the "large" and
"small" descriptions do not refer to the
actual physical size of the speakers, but
their ability to reproduce low-frequency
sounds. If you are in doubt as to which
category describes your speakers, consult
the specifications in the speakers' owner's
manual, or ask your dealer.
With the AVR65 turned on, follow these
steps to configure the speakers:
1. Put the AVR65 in the Dolby Pro Logic
mode by pressing the
Dolby Pro
on the front
Logic Selector Ó
panel or by pressing the
on the remote,
Mode Selector y
followed by the
buttons
⁄
¤
/
until
appears in the
PRO LOGIC
Main Information Display U
the
indicator
PRO LOGIC
AVR65 120 volt Rev (C) 10/6/98
System Configuration
2. Press the
the remote or front panel. The words
FRNT SPEAKER
the
Main Information Display U
If you are using the on-screen display
setting
system, a display will appear indicating
the status of each speaker (Figure 2).
M O D E
setting for
F R O N T
C E N T E R
S U R R
S U B W O O F E R : O F F
M A S T E R
Figure 2
3. Press the
4. Press the
remote or the
on the front panel until either
LARGE
match the type of speakers you have
at the left front and right front posi-
tions, as described by the definitions
shown below.
When
SMALL
frequency sounds will be sent to the
Surround
subwoofer output only. Note that if
you choose this option, and there is
g
no subwoofer connected, you will
not hear any low-frequency sounds
and
from the front channels.
lights.
F
18
button
x ˘
on
Speaker
will appear in
.
: D O L B Y
P R O
L O G I C
S P
:
L A R G E
S M A L L
S P : L A R G E
S M A L L
N O N E
S P K
: L A R G E
S M A L L
N O N E
O N
V O L U M E :
1 9 D B
button
.
i ˜
Set
buttons
on the
g
⁄
¤
/
buttons
¸
Selector
or
appears to
SMALL
is selected, low-
When
is selected, a full-
LARGE
range output will be sent to the
front left and right outputs, and
NO low-frequency signals will be
sent to the subwoofer output.
NOTE: If you are using the On-
Screen Display system, the selected
speaker option will appear in high-
lighted video. The selection will
change in response to the steps
outlined on these pages.
5. When you have completed your
selection for the front channel, press
the
button
, and then
i ˜
Set
press the
buttons
on the
g
⁄
/
¤
remote or the
buttons
Selector
on the front panel to change the
display to
CEN SPEAKER
6. Press the
button
i ˜
Set
and use the
buttons
g
⁄
/
¤
the remote, or the
Selector
on the front panel, to select the
¸
option that best describes your system
based on the speaker definitions
shown above.
When
CEN SP SMALL
selected, low-frequency center
channel sounds will be sent to the
subwoofer output only. Note that if
you choose this option and there is
no subwoofer connected, you will
not hear any low-frequency sounds
from the center channel speaker.
¸
.
again,
on
buttons
is
Hide quick links:
Advertisement
Table of Contents
