Resetting The Remote - Harman Kardon AVR 635 Owner's Manual

rename the DSP Surround Mode Selector
which is normally not used when DVD is selected,
so that it reads ZOOM in the remote's display.
1. Press and hold the Program Button
about three seconds while the message shown
in Figure 24 appears in the remote's LCD
Information Display . Release the button
when the red light under the Set Button q
appears.
2. The remote's MAIN MENU message (Figure 25),
will appear in the LCD display and the Set Button
q will remain illuminated in red. Press the
Navigation Button o until RENAME
⁄ / ¤
appears on the bottom line of the LCD screen,
as shown in Figure 74.
3. At the next menu screen press the
Navigation Button o until RENAME KEY
appears on the bottom line of the LCD screen, as
shown in Figure 77. Press the Set Button q
to continue.
R E N A M E
R E N A M E K E Y
Figure 77
4. The next display screen (Figure 78) selects the
device within which the key to be renamed exists.
Navigation Buttons o until
Press the
⁄ / ¤
the name of the base device appears. In our
example, since we want to rename a button within
the DVD device memory, DVD should appear in
the lower line of the LCD. When the desired
device name appears, press the Set Button q.
S E L E C T A D E V I C E
D V D
Figure 78
5. At the next menu screen, select the first button
within the device to be renamed, as instructed in
the display shown in Figure 79. Select the button
by simply pressing it on the remote.
S E L E C T A K E Y
Figure 79
6. Depending on whether or not the button pressed
already has a named function within the device
selected, one of two things will happen.
a. If the button to be renamed already has a pre-
programmed, or previously renamed title in the
remote's memory, you will see that name on
the top line of the LCD display, and a blinking
block cursor will appear on the far left side of
the bottom line of the display, as shown in
Figure 80.
,
D I S C S K I P
Figure 80
for
b. If the button to be renamed does not have a
function in the device selected, the top line of
the LCD screen will be blank, and a blinking
block cursor will appear on the far left side
of the bottom line of the display, as shown in
Figure 81.
Figure 81
7. To enter the new name for the key, press the
Numeric Keys
numbered buttons indicate which letters or sym-
⁄ / ¤
bols will appear when the button is pressed during
the renaming process. The first press of the but-
ton will enter the first character shown, subse-
quent presses will change the display to the other
letters above that numbered key. For example,
since the first letter we need to rename the Tone
button to Zoom is a "Z," so you would locate the
"Z" above the "9" button, and press the button
four times. The first press shows a "W," the subse-
quent presses step through the other letters avail-
able until the "Z" appears. Consult the table on
this page to see which characters are available by
pressing a particular button.
8. After you enter the first letter of the new device
name, there are three options for entering the
next character:
a. To enter a letter that requires a different numeric
key to be pressed, simply press that button.
The cursor will automatically move to the next
position and the first letter accessed by the new
button will appear. Following our example, the
next letter needed is an "O," so you would press
the "6" button once.
b. To enter a letter that uses the same numeric
key, you must first press the
Button o to move the blinking cursor block
to the next position. Then press the Numeric
Key as required to enter the desired letter.
This is the way you would enter the second "O"
in the word ZOOM, and again for the letter "M. "
c. To enter a blank space, press the
Button o twice. The first press will move the
cursor to the right, and the second press will
move the cursor one more space to the right,
leaving a blank space between the last letter
and the next one.
CONFIGURING THE REMOTE CONFIGURING THE REMOTE
9. Repeat Steps 7 and 8 as needed to complete
10. When the text entry is complete, press the Set
11. At this point you have two options:
. The letters above the
NOTES ON RENAMING KEYS:
• Renaming a key does not change its function. You
may change the function of an individual key by
learning a new code into the remote. See page 41
for more information.
• When a key is renamed it will only apply to the
specific device selected in Step 4. The same key
may be renamed as needed for each individual
device with which it is used.

Resetting the Remote

Depending on the way in which the remote has been
programmed, there may be a situation where you wish
to totally erase all changes that have been made to
the remote and return it to the factory defaults. You
may do that by following the steps shown below, but
remember that once the remote is reset, ALL changes
that have been made, including programming for use
with other devices, learned keys, macros, punch-
through settings and key names, will be erased and
› Navigation any settings you had previously made will have to be
reentered.
To erase all settings and reset the remote to the
original factory default settings and displays, follow
these steps:
1. Press and hold the Program Button
› Navigation
2. The remote's MAIN MENU message (Figure 25),
CONFIGURING THE REMOTE
entering the needed letters, numbers, characters
and spaces.
Button q. The new name will be entered into
the remote's memory, replacing the default name.
a. If you wish to program an additional key within
the same device, press the Set Button q as
instructed by the bottom line of the LCD display
reading ANOTHER KEY. The remote will
return to the SELECT A KEY menu option
as shown in Step 6. Repeat the instructions in
Steps 6 though 11 to rename the next key.
b. If you have no additional keys to rename, press
Navigation Button o once so that
the
⁄
the menu screen displays EXIT on the bottom
line of the display. Press the Set Button q
to return the remote to normal operation.
about three seconds while the message shown
in Figure 24 appears in the remote's LCD
Information Display . Release the button
when the red light under the Set Button q
appears.
will appear in the LCD display and the Set Button
for
51